DBL333EBC General Electric Dryer - Instructions

Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.

Scared to do the work myself found this website which gave me basic instructions and access to parts needed. Ordered and made an error called and CS took care of me right away. Fast friendly and will buy from them again. Great service great parts and great people!

The repair for the average untrained mechanicslly inclined " first off google directions/instruction picture step by step " we took off the wrong part which made this job difficult there is a part on the back that was removed prior to guided directions, called parts select they are awesome"our belt was delivered the next day on a 3 day weekend I was suprised second correct part sent anyone who took on this job , they will appreciatte all this . the belt was fairly easy to repair just do as directed follow guidelines. difficulty detaching a part that never should be"pain in the a" order your part from this company they rock" and picture guide and specific direction guideline @ this dryer has well outlived the money spent still kicking strong after several years of use hotpoint dryer

Had to pry dryer front off drum because buttons had caught between glide and felt causing excessive heat that melted the glide to the felt. Removed old felt from dryer front and replaced glide then reassembled machine. Took longer overall time because I did not realize two glide parts were needed so repair was delayed until second glide was received.

Checked all thermostats, they were good. Circuit was getting 220 vac. Eventually found fuse in the back near the heating element, same was bad. By-passed same, and when we did, the timer Popped & arched !. Not sure why. Motor protectrion fuse found to be good. Heating elements good. Fuse was the only bad part found, never figured out what caused it to blow. Appliance was taken away after purchase of new one. Problem not found or resolved by self diagnostics. Originally the exhaust duct was somewhat clogged with lint, but not severely.

i folow the instructions from web page

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

Top control panel removed; next used screwdriver to lift up dryer top on each side( the top of dryer is attached by clips on the underside) the dryer front panel has two screws, one on each side of inside front(they are easy to reach and near the top of the inside front panel, after removing these two screws we used screwdriver again to pry off front panel as it is attached also by clips on inside of front panel. At this point there is easy access to the drum where the old belt was removed, new belt put in place; removed small panel on back of dryer to access idler pulley and attached new belt through the pulley; turned the drum a couple of times by hand to check if belt was running true on the drum; problem fixed.

Put in the new switch and it starts great. Now that it runs there is no heat. I assume the elements are out.

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank

Depending on the condition of the bearing there are two methods described here to change the bearing, the first (and easiest) is if the bearing saddle was not damaged to the point of not allowing the bearing to lift out of it and the second is for when the saddle is damaged.
There are a few items common to both methods so I will start with them and with the belt release.

Parts Needed
Bearing and Shaft kit. Do not bother replacing just bearing or just shaft, do the kit as it is the bearing/shaft and saddle and comes with new ball bearing and grease.
Belt. if going through all this trouble replace the belt while there.

Tools needed:
8mm open/box wrench
good philips head screwdriver
a stubby philips screwdriver
putty knife or wide flat screwdriver
some duct tape

ACCESS

First, unplug the power to the unit and shut the gas off. You'll be working around the motor and burner so this is needed.
Then using the putty knife or flat screwdriver remove the top panel by depressing the latches in the horizontal seam on the front side approx 2" in from each corner.
remove the panel and set it out of the way.
Now unhook the door sensor wires and mark or store them in a manner so you will remember which side of the switch they plug into.
On each corner approx 6" down there is a philips screw, remove these and tilt the front panel forward (to clear the drum and duct seals) then lift upwards to remove the door panel.
Set this out of the way too.

REMOVE BELT FROM MOTOR

The motor pulley and tensioner are hard to see but can be done blind just by feel, they are on the lower right front side of the unit. Reach in on each side of the motor and with left hand push the tensioner towards the right side while with right hand pulling down on the tensioner spring (its a weak spring) to release it from the metal tab on bottom.
Once this is down the tensioner will move to the left and the belt can be removed from the drive puller easily.

At this point you can slide the belt forward and remove it and slide new belt on if you are only doing a belt replace.
Install procedures will be listed below.

REMOVING DRUM

FOR NON-DAMAGED SADDLE

If the saddle is not damaged you can now jerk up (not too much force) on the rear of the drum and this will pop the shaft bearing end out of the saddle. Then carefully slide the drum forward through the cabinet to a palce you can access it easy.
Remove the shaft and bearing from the drum by removing the three phillips screws whose heads are inside the drum.
Now remove the saddle from the cabinet by removing the 2 bolts (8mm head) that go trough the rear, there is a ball bearing in the saddle that may be useful to save in case you drop the new one and there is a screwplate on exterior rear that will fall when you remove the final bolt.

FOR DAMAGED SADDLE

If the saddle is damaged (distorted) the procedure is a bit different and quite a bit harder, but not awful bad. It adds about 20 to 60 minutes extra (depends on how the screws come out) to the whole job.
First remove the drum from the shaft by unscrewing the three philips head screws from inside the drum and, like in prior method, carefully pull the drum through the front of the cabinet and set it aside.
Then to remove the saddle you may be able to remove the two 8mm head bolts by flexing the plate to the side and loosening each bolt a bit while alternating. However I had to actually move the burner ducts a bit to get at mine as I could not turn the left side bolt.
This is where the stubby screwdriver is needed, there are 4 philips screws whose heads are hidden by the seals on the ducts, by folding the seal back a bit you can access them. I was able to just do the three at the top, left, and lower left and slide the duct a bit to allow wrench access to the bolt. I did not have to remove the lowest screw myself but you may need to.
Always make sure to not bend the tin too much and this will hurt heat movement through the system.
Once you have the saddle removed, rememberi

I took the top and front off the dryer. I then took the screws out of the drum and removed the drum. I then took the old bearing out and put the new one in.

The job is simple once you know how to remove the front panel. The steps are as follows:
1. disconnect the power cord.
2. remove 4 Phillips-head screws under the lip of the front panel that secure it to the top panel (#1 point Phillips-head screw driver)
3. swing the top panel up, it is hinged in the rear.
4. making note of the connection points of the color-coded wires, disconnect the wires to the lamp socket and door switch (I used a felt-tipped pen on the inside of the front panel to mark the connection points, "R" for red, etc.)
5. remove the upper 2 hex-head screws from inside of the front panel (5/16" nut-driver)
6. loosen the lower 2 hex-head screws (5/16" nut-driver) accessible from outside the panel (you only have to loosen them since the bottom mounting tabs are slotted)
7. slightly lift (to clear above mentioned lower tabs) and tilt the front panel toward you. Swing the front panel to the right as though you were opening a door and position so it does not fall.
8. remove 10 hex-head screws from the black lower rear access panel (5/16" nut-driver) and remove the broken drive belt. Note that the narrow black panel securing the power cable can remain in place.
9. at this point take advantage of the situation and vacuum out the years of lint and dust you could not reach before.
10. stand in front of the dryer, lift the dryer drum slightly and slip the new belt (rib side down) around the drum. Position the belt near the rear of the drum along the wear-mark left by the old belt.
11. go to the back and place the belt in the motor's drive-belt pulley, making sure the ribbed side of the belt mates with the ribs in the pulley.
12. position the tension wheel so that the it takes up the slack in the drive belt. Note the flat side of the drive belt will mate with the flat of the tension wheel.
13. spin the dryer drum a few turns by hand to make sure the drive belt lines up properly with the pulley.
14. reassemble the dryer by reversing the above steps, starting at step 8.

Replaced the start switch.

disassembled chassis of dryer, unbolted top, lifted top to expose drum. bolted top back on. resumed repair next morning. unbolted top. lifted drum (it moved up and down about 1 inch) and got new belt around it. rebolted top down. tipped dryer to its back. unbolted and removed panel at bottom, exposing drive motor and tensioner spring. positioned belt around drive motor spindle and tensioner spring. replaced panel. reconnected dryer to electricity. reconnected gas using new flexible connector.