DB120P1 Frigidaire Dishwasher - Instructions

At first remove the lower rack to give more room for you to lean over the inside of the dishwasher then remove the old gasket tub 90 inches long make sure that you know which side goes where, so that it will be easy to put the new one. Then press the gasket firmly on the side.Now you can start your dishwasher with no leak and saves you a lot of money for buying a new one.

The repair was simple. When the part comes, you may need a hairdryer to heat up the plastic a bit to get any kinks that may have happened during packaging or shipping, very easy 5 minutes. Removed the old gasket by hand, very easy, 1 minute. You will need to clean out the track that the gasket sits in. Mine had years of black gunk inside of it. You will need qtips or a small screwdriver with some tissues or papertowels, easy but took 15 minutes to clean out properly. Installed new gasket in the track, start at the top middle, there is a notch on the gasket so you know where the middle is. Installed by hand, just push bottom edge into the clean track, easy 5 minutes. Ran the dishwasher with no leaks. Very pleased with the result and how easy the gasket was to remove and install.

I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.

Snapped new wheels into place on the axel. New wheels were exactly like the old ones

used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

I removed the front panel below the door. There are 4 Hex screws, two at the top (accessible with the door open) and two at the bottom. After removing the screws, the panel came off, and I could reach inside to replace the springs. I found it easier to use a socket wrench than a screw driver.
Easily done. Anybody can do it. It took longer to clean up the panel than to do the actual repair.

very simple to do....attach spring to door...stretch to hole in frame and attach there...easy as 123

I snapped on the new roller and bingo! problem solved.

Removed the "kick plate" (4) screws. the hard part was attaching the springs to the door hooks. you cannot see them, have to go by feel. then stretch them to lower frame. attached the lower door trim piece with three screws.

Snapped the new one in. One second repair - like new.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

Replaced the gasket

Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.

Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.