CWL2000R*119 General Electric Washer - Instructions

Repair was relativly simple. I read previous customer direction submissions. I found that laying the front of the washing macine down removing the back panel gave easy access to the water pump. Remove all 4 hoses first then with a 11/32nd socket remove the top 3 screws that are holding up the pump. At the bottom of the pump unscrew the clamp until the pump will slide out of the rubber stabelizer.(Leave stabelizer attached to the motor) Remove the pump and in reverse order replace with new pump leaving the back cover off of the machine. Set the washing machine upright and check for leeks. After checking for leeks attach the back panel onto the washing machine.

Popped the top by pushing in front clips with screwdrivers. Removed spin shield. Removed agitator and hub cover (all by hand). Used 12pt. socket to remove three bolts holding the tub. Pulled up tub (difficult b/c of weight and slippery residue). Loosened clamps w/ nutdriver and removed boot. Scrubbed clamps clean and reinstalled everything.
Forgot to get clamps really snug, so it dripped a little. Did everything second time, but before replacing tub, did a leak check by running a load. Worked great. Good luck.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

Laid washer face down, unscrewed the 3 screws holding part to brackets. Removed the hose connections to the pump part. loosened the clamp around the base of the pump and pulled the part out. inserted new pump, tightened the clamp, reconnected the hoses, and bolted the part to the brackets. First time through, one of the hoses was not tight enough, so we put a new clamp on it and it worked fine.

repair was quick and part came quickly. I was very satisfied.

Took the back cover off 6 screws, took the inlet valve off the mounting plate 2 screws, the vater valve off the mounting plate 2 screws, and disconnected the inlet valve clamp from the inlet hose to the washer. In reassembling reversed the process. Best part; G.E. was going to charge me $59.00 for the valve, and I got it for $16.10 shipped in one day.

My appliance repair man replaced the inlet hoses into the washing machine and in doing so damaged the threads on the hot water inlet which resulted in a seriuous leak. I removed the 4 screws that held the damaged water inet valve (#PS270305)in place (inlet valcve and solenoid), removed the 4 wires to the solenid (noting the order in which they wree attached) and simply reattached the electrical wiring and screwed the inlet valve in place with the 4 screws that I had taken off to remove the old part.

I removed 2 screws on the top control panel to tilt the panel back. Then "popped" the hinges. I then removed 2 screws on the rear panel, to "pick up" the panel out of its locking position. Then the rear panel was loose. I removed the 2 srews holding the water inlet valve to the panel, removed the hose and placed the new water inlet valve in position. Assembled everything back to gether. After a $16.00 part was replaced, the washing machine worked like a brand new one with very high water flow. It was a very simple task to do on your own.

I disconnected two wires on back of inlet valve,then I removed the plastic hose connected to left side of valve. Removed old valve and replaced it with the new one.Attached hot/cold hoses and turned on washing machine to check for leaks.

I changed the Water Inlet Valve in less than 15 minutes. The valve fit exactly, and the water hoses fit right on. I turned on the water and the washer filled without hesitation. The cost was 15.00, this beat the 62.00 price I was given by GE for the part alone.

i Had washer up side down took puly out and transmission seal out used screw driver install your part add seal on it tap it back in used socket added quartz of gear oil90 as recommended put every thig back it good experience and saved hundreds of dollars for new ones thank so much for ur video and ur technical people on your site

I did watch the video, that Parts Select included in an email. After that just follow the instructions in the video. You do need two people to do the job, since the belt needs to be tight. One for holding and one to tight the screws.

Pulled off the handle with the kneedle nose pliers replaced the plastic piece in that, then pulled off the plate that turns the machine on and just snapped the new one on. Only took seconds and saved alot of money. Considering just to have a repair man come to see what was wrong would have cost me $88.00.

Could smell burning rubber as it tried to spin, so figured it was the belt. No, I did no do it the hard way by removing the screws etc. I threaded the belt on the pulleys on one side, and slowly turned them, using my fingers to force thread the belt into place. Worked like a charm.

I emptied the washer and unplugged it from the wall. Then i pulled it out so I could get behind it. Next unscrewed the water hoses from the washer. Removed the plate holding the water inlet valve by unscrewing 2 screws holding it to the machine (I used Vise Grip/pliers). Note which side of plate goes up/outward so you can put it back on! Removed 2 more screws that hold the valve to the plate. Remove clamp from valve end to disconnect valve from tubing with a screwdriver. I was able to remove the tubing with a twisting motion even though my washer is way over 10 years old. Remove 4 electrical clips from the valve by pulling them out, (REMEMBER the order of the electrical wires!!). Install new valve by doing this in reverse. Then run test cycle, success and saved hundreds of dollars!