CWG3100AAS Maytag Wall Oven - Instructions

Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I removed the broken section of the screw.

Got the part, changed it, works great. That's all

Unplugged the oven from electricity. Took off the bottom(Floor) of the inside of the oven. Checked that the new part looked the same as the old. It did. Then I checked the back of the oven, had to take off a cover, and the connector in the back was not the same. I did not that it had the same two wires so rather than send it back, I figured I could make it work. I started to take off the old piece by unscrewing the two screws. They were a bit rusted, one came off the other I had to hacksaw and twist off. I cut the old connecting end off of the old part and the end off of the new part stripped the cover off the ends of the wires, and put the old end to the new part, having also put the old wire covers over the new wires. then twisted the end together and wrapped the in electrical tape. I had to take the piece that held the new part out of the oven the tried to use the one semi-good old screw, then some newer screws, then finally used some new nuts and bolts to connect the part tightly. put everything back together and it worked.

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

I replaced the igniter.

took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.

unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.

took oven door off, took oven racks out, removed heat sheild, took 2 nuts off ignitor, removed ignitor, gently pulled ignitor wire out from back of oven, unclipped wire, clipped new ignitor to wire harness, replaced nuts to install new ignitor, replaced heat shield. replaced oven racks, replaced oven door, tested to make sure oven lite, took about 10 minutes!!

removed oven door and shelves and lower pan and replaced igniter

Followed the instructions that were provided me when I ordered the Gas Oven Igniter

opened the oven door, remove racks, remove lower drawer, unscrew protective panel on lower part, take out the bottom plate, unclip the old igniter, clip in new igniter, put everything back together and you are done!

Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.

easy

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.