CWE23SP2MCS1 General Electric Refrigerator - Instructions

EXCHANGED THE LED LAMP ASSEMBLY. ONLY DO ONE AT A TIME AS THEY ARE WIRED IN SERIES!

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I searched and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.

Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.

Repair man thought it was the control board and an issue with a relay on the board. Purchased the new board but found out the board was fine, and it was the recirculating fan that would go out intermediately.

Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a replacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.

Watch this very good refrigerator evaporator fan replacement video

Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

Remove old filter by pulling and not twisting and insert new filter by pushing in place.

Received the wrong spring. It is larger in diameter and the legs are too long. I used pliers to modify the spring for a temporary fix. Emailed CS about the wrong part and have never received any response back?

This was the first time I took out the old filter on my new refrigerator and added the new one. It was a little hard getting the old one out because I was afraid to pull on it but it did come out ok and was easy to put the new one in.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

followed install on line

Our fridge sits within our cabinets with one over top of it. That plus the leveler feet to secure it in place made this easy task a little more difficult. I was able to remove the top panel to access the switches. I was concerned, as I had not unplugged it because of the feet and went for it regardless, figuring if there was a shock, it would be minimal.

I was able to switch out the switches no problem. The only problem is it did not resolve the issue with my lights.