CVM1790SS4SS General Electric Microwave - Instructions

First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!

Removed door from microwave. Pried inside door trim off. Removed 4 small retaining screws then pried inner door section out revealing the 4 screws holding the handle in place. Removed those screws installed new handle using 4 original black screws. Reassembled door in reverse sequence from above. Attached door to microwave and admired my work.

I looked at the exploded pic on your web site to find the location of the sensor. Next I removed the cover by unscrewing 15 screws then swaped the sensor and re assembled! Works great! Fixing it my self I saved at least 150$ and did not have to wait all day for a repair man who probaly would not have the part on the first visit.

the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience

Removed one screw, removed cover, and replaced lamp. Pretty straightforward.

Looked on line and found a you tube that said to check the door micro switches (there are three of them. Found one of the switches had an actuator that was stuck down. I got the actuator working but problem was still present. Another you tube showed how to repair the contacts in the switch and that solved the problem. however the plastic piece that holds the switches was broken and would not hold the switches securely. Ordered that piece and a new switch. Remove the vent plate on top (one phillips) and the control panel (one phillips). The switch holder is held in place with 2 phillips and is a little tricky to get it out and undo the wires. Once out, it's just a matter of putting the switches into the new holder and reinstalling it. Google the model number and the problem and there's virtually a you tube to repair ANYTHING.

It is easy to repair the burnt out bulb if one has the correct bulb. Your website is very user friendly and your service is great. I was not able to replace the bulb at this time because our RV is at the repair shop for some other matters. I am sure the installation of the new bulb will go smoothly. Thanks for asking. Sharry Kiehl

Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.

Just placed it in microwave

We had our kitchen remodeled; new cabinets, countertop, range, refigerator, microwave, dishwasher and floor.

The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.

A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.

The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!

Bob
Racine, WI

Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a new one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.

Ordered the part. 2 days later part arrives. Took me 30 seconds to install the part. Sorry it was not more eventful.

I was surprised to find that the turntable for my 10 year old GE Profile microwave/convection oven was not readily available at my local GE retailer. I ordered the part from this website hoping that my order would be filled. I received an immediate response from customer service and the part was on my front doorstep in under 1 week! I would order from this website again!

Easy to repair. One screw, remove bulbs, replace with new ones, secure screw.

Partselect.com shipped items quickly as promised, provided follow up email confirming receipt of order, a second email confirming shipment & a link to check shipping status.

Would not hesitate to do business with Partselect.com again!!!

1. Open the cover over light bulbs with screwdriver.
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.

Now, was that easy or what!