CVM1750SH2SS General Electric Microwave - Instructions

Remove microwave and set on flat surface. Remove all screws on top. Remove all screws around back edge holding top on. Finally remove the screws on botton holding top on and remove top. On left side on top, remove 6 screws holding black channel in place. Also remove 3 screws holding metal top in place. Now lift black channel up and unplug 2 wires on cutout. Replace cutout and reinstall everything in reverse order. Worst part is taking microwave down and reinstalling.

just slipped the filter in place.

The spacesaver is mounted over the stovetop. I removed the oven, then removed all the screws from the cover. Removed the cover and located the TCO and removed the wiring and the TCO. Ordered the part VIA internet and replaced it . It helps a little that I was Radar tec. and taught Electronics for 10 years and repaired lots of Microwaves. However anyone could do it just watch what you remove and replace in reverse order.

This is the second time replacing this fuse, last time was exactly one year ago. The first time I replaced it, I removed the oven from the wall & disassembled a number of things to reach the culprit. This time I left the oven mounted & was able to access the 2 grille mounting screws on the top of the grille & remove it. Next comes the black plastic air deflector held by two screws & is mounted in front & on the right, it is shown on the parts list just above part #1434. After removing it, remove the two silver cover screws in the front, this cover also doesn't have a part # but is shown to the right of part #1410. At this point you can lift this cover enough to access the fuse which is on the left & held in place by one tiny screw through the clamp at the top, (careful not to drop it when removing). PS: Don't forget to cut the power to the microwave before starting!

Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.

This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.

One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.

Removing interconnect switch is tricky but not difficult.

Outer cover replacement is not as easy as it should be, especially the sides.

All is well and working.

Microwaves are simple devices if you are know how to read and understand schemetic diagrams.

We had an accident on Christmas day, while using the convection option on the microwave, the glass plate and ring assembly slipped down from where it was temporally being stored, and shattered into many pieces.I was really lucky, we had a older GE microwave that we scrapped out. My wife and I decided to keep the glass plate and rotating ring, when we tried the parts it wouldn't turn. I decided to try a new rotating ring considering the glass plate would of cost quite a bit more. When the part came, I tried the ring and as I said I was really lucky, it worked perfectly. The ring from the old microwave made the glass plate sit too high and consequently wouldn't turn. It wasn't really much of a repair, but it all worked out great, the parts site was easy to use and the parts came when they said they would.

This was the second time I've had to open up the microwave. 1st time display would blank out but system would continue to operate. Found solder connections on board to LED display were defective. Resoldered and unit was fine. This time I found the connection to the oven cavity temp cut-off was bad, plastic connection cover melted. When unit operated bottom lead and wire would heat up. Couldn't measure a Discernable distance so either wire or connector connection surface was not sufficient to carry the current. 1st replaced sensor still wire heated up. Replaced connector and there was no sign how heat from resistances.

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

took old tray out put new one in. works great now.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

I just needed to remove 2 philp screws and insert filter. The filter fit perfectly and perfomred as expected.

I looked at the exploded pic on your web site to find the location of the sensor. Next I removed the cover by unscrewing 15 screws then swaped the sensor and re assembled! Works great! Fixing it my self I saved at least 150$ and did not have to wait all day for a repair man who probaly would not have the part on the first visit.

Removed door from microwave. Pried inside door trim off. Removed 4 small retaining screws then pried inner door section out revealing the 4 screws holding the handle in place. Removed those screws installed new handle using 4 original black screws. Reassembled door in reverse sequence from above. Attached door to microwave and admired my work.

First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!

removed two screws, set in place. done. The best parts was that your ordering and shipping was out of this world. Never thought I would get the Filter that fast. Thanks You made my day.