Models > CTX14LATARWH > Instructions

CTX14LATARWH Hotpoint Refrigerator - Instructions

All Instructions for the CTX14LATARWH
31 - 45 of 48
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
family member melted fan with hair dryer
Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.
Parts Used:
Evaporator Fan Blade Kit
  • Lauraine from Rocky Hill, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken light switch
took a little more effort than the video show to remove old module and replace new. Works fine now.
Parts Used:
LIGHT SWITCH
  • Ted from SANDWICH, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light was flicking
It was way to ez to install only a couple of minutes that's it
Parts Used:
LIGHT SWITCH
  • Stephanie from KEARNY, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan blade broken
Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.
Parts Used:
Evaporator Fan Blade Kit
  • John from Cumberland, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Parts Used:
LIGHT SWITCH
  • Don from Eugene, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Parts Used:
LIGHT SWITCH
  • Patricia from Sylva, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Parts Used:
LIGHT SWITCH
  • Victor from Fort Myers, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Parts Used:
LIGHT SWITCH
  • Cynthia from Seatac, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Parts Used:
LIGHT SWITCH
  • Jules from Crowley, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Parts Used:
LIGHT SWITCH
  • christopher from collegeville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Unit not turning off after reaching set point
It went great! Parts ordered were exactly what I needed. Installation was quick and easy and everything working perfectly.
Parts Used:
Temperature Control
  • Scott from Bloomington, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The bottom part of fidge was warm with water droplets on the its ceiling.
Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Parts Used:
Evaporator Motor Kit
  • Charles R from Renton, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
light switch quit working
removed the inside fridge electrical panel and swapped switches
Parts Used:
LIGHT SWITCH
  • David from Simpsonville, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Parts Used:
LIGHT SWITCH
  • ANTHONY from NEW EGYPT, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Compressor not coming on
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.
Parts Used:
Capacitor
  • Kevin from Morris, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CTX14LATARWH
31 - 45 of 48
Back to Top