CTS18ABMERWW General Electric Refrigerator - Instructions

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Despite attempts to quiet the 2 year old fan, I went ahead and replaced it. Part Select was prompt with a new one at my door less than 24 hours. It was just the fan motor, so took a couple extra steps to place it in the metal housing, but no problems and though the frig still makes noises, it's not coming from the fan as before.

First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut and checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.

Followed the instructions on the repair video and it made very easy. Also saved us a lot of money. Thanks for your help.

After reading the trouble shooting section of the owners manual, I determined, without much difficulty, that the temp control was defective. I checked some local outlets and found the prices running from $36.00 and up. The same part from this site was around $20.00. Guess where I bought mine! It arrived in a timely fashion, and I installed it with no problem, in about 10 - 15 minutes. This was a very easy job, just remove and replace three wires snap the unit into place, and screw the cover on. Tip: I always use you tube or another source to get some instruction, just in case I'm not as smart as I think I am!

Shelf cracked when less than year old. and has gotten progressively worse thru the years.
Replaced in seconds , no tools required .
I should have done this years ago

Took back out of freezer compartment, pulled plug and removed old motor, inserted new parts. It was
easy and the parts arrived the day after I ordered
online, even though I chose the cheapest shipping
option. Nothing in my freezer had a chance to thaw
out.

Open freezer, remove rack....this got a little complicated because I had to remove the door, that required the offset screwdriver because I had a clearance issues preventing the door from opening all the way. Remove the panel covering the fan, unplug the fan, remove it from bracket, install new fan, plug in, replace panel, replace rack, replace door...bam all done!

Went on YouTube and it had excellent instructions for removal and installation

I haven’t received the wheel yet. Originally ordered on Dec. 13. Hadn’t received it by Dec. 20. Finally shipped on Dec. 22. Tracking said it was expected to be delivered on Jan.2. Not delivered. Then it said it was still on its way but it was unknown when it would be delivered. Still waiting on Jan. 6. By far the most expensive economy shipping ever, as this refrigerator is in a rental that can’t be rented until a wheel is installed.

Pulled the door off easily and noticed that the spacer on the Center hinge was ground down to nothing and that a small screw in the bottom plate of the door was half way out. This screw would catch on the cabinet Center hinge bracket and stopped the door from closing. Problem was solved by tightening the screw and putting in a new "spacer" that kept the small screws from contacting the Center hinge bracket. The freezer door now closes like new.

two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge

The hardest part of the repair was emptying the freezer, next was getting the fan off of the motor shaft, The only reason the job was difficult is because i am 67 years old and not as flexible as i used to be.I had a tough time getting the fan off of the motor shaft, but i got it off with the use of a vise, and had to use the hammer and a socket to install a new fan blade.

First I removed the two screws, the fan and unpluged the electrical connection. Then, plugged in the new part and then screw it back together.

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...