CSX27DRXFAA Hotpoint Refrigerator - Instructions

Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.

I had read from your sight, to simply cut the lines at the reservoir and tape the new lines to the old. Then use the old lines to pull/feed the new lines to the coupler/valve. This worked great and greatly decreased the time it took to install. I spent more time moving out the frig and cleaning up all the dust (probably should do that more often)

I replaced tie ice Dispenser Plate & thye ice Bucket Auger.I read the previous installation instructions written on this website first.Good info! I copied the Parts diagram on the website, this really helped. I also took my phone camera and took pictures as I was taking the parts apart. The only problem I had was with the Wire Actuator Display Rod,making sure the spring tension was correct and positioned the correct way when I reassembled it. I was able to look at my pictures and assemble it back the correct way. I put the ice bucket assembly back in the refrig and it works great. No more rusty Ice!!!!!!!!!!!!!!

replaced circuit board and water solenoids

Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.

The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!

pulled fridge away from wall, shut water to fridge disconnected both lines,back one and front one.Removed old water resevoir 1 screw. cut old lines at resevoir. used small threaded rod (1"long)to connect old lines to new lines and taped together,pulled new lines with old lines and reconnected.No lifting of fridge,actual repair under 1 Hour but took longer because I cleaned underneath really well and took my time.

I removed the ice container with the auger inside. I removed the front panel, then the auger and housing. I had to clean all of the parts that had rust on them. I got some of the parts mixed up and was having a hard time putting them back where they belonged. I went back on the PartSelect web site and with my IPad and opened the exploded view of the parts. This enabled me to put the auger back together. It works perfectly now. Saved a lot of money by doing it myself. Thanks PartSelect.

Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Just replaced the auger from the old one

Looked at the instructional video and read previous customer comments. Didn't have to dissassemble rear of freezer door. Access through the front once trim ring and circuit board removed. Could not have done it with out the video/and or previous customer comments. Part was shipped and received immediately. Repairs complete! No more frost developing and plugging ice chute! I especially appreciate the customer comments on how to complete this repair!

Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.

Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.

Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.