All Installation Instructions for Hotpoint Refrigerator CSX25DRZAAA

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Had a drip which filled up the tray and leaked on the floor from water dispenser

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Parts Used:

Dispenser Door Assembly or Flapper

Rudy from CITRUS SPGS, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing

I just followed the instructions on the video and it was exactly as they said......no surprises.

Parts Used:

Dispenser Door Assembly or Flapper

Joe from BRICK, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

On the water dispenser line, the heat from the compressor unit had cracked the feed line, resulting in a leak.

I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting with a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.

Parts Used:

Water Tube and Grommet Kit

Walter from SANDIA PARK, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Original part cracked allowing crushing fingers to grab plastic guide jamming it.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Parts Used:

Crusher Dispenser Housing

Barry from SUN VALLEY, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Change bulb

Easy

Parts Used:

Light Bulb - 40W

Louis from LEAGUE CITY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

froze in freezer

unclipped and replace with new part.

Parts Used:

Dispenser Door Assembly or Flapper

Ken from Wesley Chapel, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker discharge was slow and jammed with ice and frost. The cause was a distorted flapper that did not seal properly, admitting warm air into the dispenser chamber.

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Parts Used:

Dispenser Door Assembly or Flapper

Al from River Edge, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

In-Door Dispenser Didn't Work And Leaked Water

1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten screws, 7. Replace flapper. 8. Replace other parts in reverse order.

Parts Used:

Dispenser Door Assembly or Flapper

Jabe from Little Torch Key, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

rusty plate in the ice dispenser.

removed the dispenser and disasembled it repaced plate and reasembled.

Parts Used:

Ice Dispenser Plate

Roberto from Wildomar, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

replaced water tank, to the water dispencer

son did the work BUT ONLY AFTER- trying to order the part from Sears parts online, in which they never from the right part and i spent 1 and 1/2 hours on chat and finally gave up. THEN i called sears replair, made appointment for two weeks later requesting 1st repair time of the day, was asured the repair would take place between 8-12 and beacuse it was 2 weeks away it should be the 1st repair. The day of the appt I received a phone call at 11:38 saying they would be here about 12:20, I SAID NO THANK YOU< OUR AGREEMENT WAS BY 12:00. THen I got online typrd in water tank your company come up, showed photo, and price which i ordered it can in my son fixed it and all was complete within an hr.

Parts Used:

Dispenser Water Reservoir

Barbara from Frankfort, KY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Frost collected in the ice dispenser shute clogging it

Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.

Parts Used:

Dispenser Door Assembly or Flapper

George from HOSCHTON, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the ice dispencer's face plate was stainy and dirty ofcourse after a long time,it would be cleaned but for new look i reffered to change it.

I had no idea how to get the parts easily so i search on web , saw parts select.com,i read main folio of the site.which seems to me very reasonable.just one call and they delivered the part.nicely advised me if i need technical support to fix it but i was too confident and i did it.

Parts Used:

Ice Dispenser Plate

Ali from Blue Island, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice crusher did not work, Ice would plug in tub chute on discharge end.

Pulled ice tub, removed auger rotation motor and solenoid housing, removed solenoid and replaced with new one and reinstalled. Checked solenoid was working by holding freezer door open and closing switch to door an activating ice switch-- solenoid picked up. Put ice tub with auger back into freezer.

Parts Used: