CSX19LABBWH Hotpoint Refrigerator - Instructions

Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.

All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.

Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.

The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.

1. Unscrewed the top screws with a socket set 2. Took door off of refrigerator 3. Unscrewed hinge assembly 4. Put on new hinge assembly 5. Replaced door on refrigerator 6. Screwed top screws back in I watched a youtube video on how to replace it that was extremely helpful. I am not a handyman, so if I can do this, anyone can.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

1. Blocked up the door keep it steadily and enable ease access to screws.
2. Removed screws holding the door closing cam and lower door attach bracket.
3. Disconnected clamp holding the water supply line for the water and ice dispenser and disconnected the water line at the joint.
4. Removed the broken cam and put the new one in it's place, threading the water supply line through the hole of the cam.
5. Put everything back together in reverse sequence of removal.

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.

Removed trim cap at top of door. Removed two hex head screws and lifted top hinge off door. Lifted door off lower hinge. Unscrewed broken cam riser from bottom of door and replaced with new part which was then screwed into place. Replaced door on lower hinge, Replaced upper hinge onto top of door, replaced screws and replaced trim.

Easy peasy. :-)

Emptied glass shelf, removed , removed old rail. Put new rail in with original screws ,then glass shelf. Done

It was really easy for me....my son told me what part I needed. I ordered it, and he installed it!

Removed top hinge assembly to pull door away from bottom hinge (2x hex bolts) Discovered that the pin on the bottom assembly had broken off. Removed and replaced bottom hinge assembly (2x hex bolts). Aligned door with top and bottom hinge pins. Tightened all hex bolts. Done

Removed old part & screwed in new rail.
I would like to mention that the speed in which my order was sent was fantastic & your website was really easy to use. Which not being a very savvy computer person is a real compliment!! A pleasure doing business with you. I would highly recommend your company.

I followed the many post on replacing this part and everything went well. I had a little trouble getting the hinge post into the new hinge assembly, but with a slight adjustment it fell into place. I checked to see what tools I would need to do the job and had them ready before I even started. I removed the door and had it back on in maybe 10 minutes and I am not exactly Mr. Fix It. The only advice I can add to what everyone else has said is you should look the job over a little before you take the door off and have your tools ready. Then you won't have the door off for too long. I'd like to thank this site and everyone who gave advice on how to fix this problem. It made the whole job very easy.

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.