CSX19LABBWH Hotpoint Refrigerator - Instructions

Followed the video on the computer. Was fixed in no time. Works great.

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

I removed the door from the bottom hinge assembly by removing the top hinge assembly.
1. Installed the cam to the bottom of the door.
2. Installed hinge and bottom pin & cam to the refrigerator.
3. Reinstalled door and adjusted front roller height to make door close better.

Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair

First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.

I removed the drawer and glass shelf, removed 2 screws and replaced with new drawer slide in reverse order. I removed the contents of the door, the top hinge, and then laid the door down. On the bottom of the door, I replaced the pivot piece (provided) and then I replaced the hinge on the lower right side of the refrigerator box (2 screws with a nut driver bit). I now reversed the order to re-assemble the door and finally re-aligned the top hinge to adjust the door fit. Less than 30 minutes total. EASY!

After easily finding the lower hinge here through Google, I paid about $30 w/shipping and had the part in 2 days. My Hotpoint fridge was made in 1987, but it still runs well...why not fix the door?

Part repair couldn't be easier. No instructions needed...just empty the fridge door of food, remove top hinge, replace bottom hinge and plastic bushing, and reverse order to button everything up.

PartSelect.com did a great job supplying a high-quality replacement hinge for my old fridge, and it's got a new lease on life now!

My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

Part was perfect fit .Removed fan .three screws.replaced that s it

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

Easy

Remove the hinge cap on top, the loosen the bolts, remove the hinge. Pick up the door from the lower hinge, lay it down and place the cam riser on the lower hinge. Replace the door, install the top hinge and check the alignment and you are done.