CSK22GABGAD Hotpoint Refrigerator - Instructions

I simply put the two ends into the slots and VOILA...

I replaced both lower hinges without removing the doors. First a couple of observations. The hinge kit consists of two parts; the lower part (bolted to the case) consists of an “L” bracket with a plastic cam, and the upper plastic cam (attached to the door). For some reason the upper cam is available as a separate part . If both cams are plastic both are worn out. Don’t bother ordering the individual cam. If one hinge is worn out the other probably isn’t far behind. Consider replacing both at the same time. Examine the door check. It is an inverted “T” shaped bracket bolted to the door that also holds the door cam. The crossbar of the T are metal tabs that check the door swing. Way too fragile IMO. On mine the refrigerator side was cracked and broke off when I removed it. Since the stops are the same right and left. I just swapped them when I replaced the hinges. Saved $22. Replacing the hinges without removing the doors. {Warning if this technique goes wrong you will be stuck with a loaded door you can’t open.} Remove the vent grill. Stack three 2x4’s along the bottom of both doors ( 26” is about right ). Shim the door(s) up to compensate for the cam wear. About 1/8”) Use a 5/16 socket to remove the hinge from the case. Pay attention to placement of the shims and spacers. Then remove the door cam and stop bracket. Install the new door cam. Leave the screws a little loose. Replace the lower hinge and tighten the screws. Do both sides. Then carefully remove the shims and 2x4’s. Finish tightening the door hinge screws. Check the door swing. I used this technique twice. One to replace the refrigerator side hinge, then again to replace the freezer side hinge and swap the door checks. There were no problems and I saved the hassle of unloading and removing the doors.

I have just followed the instructions on the youtube video: It is really easy. I did. Thank you

put block of wood under the door, removed old hinge and installed the new one. about 15 minutes

Removed the door by removing the top hinge and lifting it off the broken bottom hinge/cam assembly. Removed the broken hinge/cam assembly found out why the cam broke the doorstop was bent so I had to order the doorstop also. The ordering of the parts was so easy. They shipped them on Monday and they arrived the next day. I will use Parts Select again

Removed everything from the refrigerator door. Removed the screw holding the cover over the top hinge. Removed the two (8mm) bolts holding the top hinge to the refrigator. Removed the door. Removed the plastic grill/cover and the two (8mm) bolts from the lower hinge assembly. Installed the new hinge assembly. Replaced the closing cam (included in the hinge assembly kit) on the bottom of the door. Put the door back on the lower hinge. Installed the upper hinge. Adjusted the door and tightened the bolts on the upper hinge, and replaced the hinge cover. Done!

removed the back of the freezer unit and replaced the defrost heater and thermastat. took the controls out of the produce side and replaced the defrost timer.

After reordering a second unit, (because the first one was cracked), I gently pushed in both sides until the unit was in place. It was a snap.

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.

I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You'll have to drill out a rivet on bottom hinge but it will save over $30.00.

Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

just shelf incerted into slots

outstanding delivery response, ordered and it was delivered the next morning

Followed the video on the computer. Was fixed in no time. Works great.