CSK22GABBAD Hotpoint Refrigerator - Instructions

Part Number: PS290199

1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.

First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!

A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.

My fridge is now as good as new.

they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .

I simply followed the excellent video, once I discovered the lower door hinge was the problem. Part Select was amazing! A $25 part and 15 minutes saved me $1,200+ ... the price of a replacement refridgerator. Thank you!

I watched the video on your web site first.Then I proceeded to do the repair exactly as the video showed. Very easy!!!!!

Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.

I took the new one out of the box and aligned it with the holes in the door and pushed down to lock it in place. Nothing else needed and no tools required.

Remoed bottom hinge and replaced broken cam riser. Replaced Bottom hinge.

Emptied contents from the door. Removed top hinge cover (one screw) and top hinge (two bolts.) Lifted door off and replaced broken cam riser on bottom hinge. Put door back on.

replace broken hinge.

Used (2) 2 x 4's as block and lever to raise door removed 2 screws and removed door used same socket to remove and replace door side of replacement part. replaced door. This is the second time I have replaced this part on frig. side. Very easy replacement.