CRSH265LB2 Frigidaire Refrigerator - Instructions

Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.

I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

put 4 screws in door handle everythings else just slides into place. took less than 10 min. frig look new again.

Very easy. I at first misunderstood the instructions. the fridge door remains closed. You pull out the water catch tray "outside" the door. someone said ice tray, thats why i thought i had to open the door to fix it. there are 3 screws that the water catch hides. once removed the control panel comes off which unplugs from bottom easily. then there are screws behind the control panel just removed. after those are unscrewed the rest tilts enough that u can uncrew the little metal bands that hold the arm. replace arm & reverse your efforts & your done. took less then 10 minutes.

The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

I ordered the complete part and installed in about 10 minutes. The order went very fast, part was in stock and everything went very smooth. PartSelect.com was very easy to work with and they have a very satisfied customer. I will definitely use PartSelect.com again. Thanks for the great service

One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

Went the typical route of part replacement since I don't own an ohm meter...pull and replace one part at a time. Started with the cheaper parts first, replaced the freezer fan for $40, same problem. Replaced the defrost heater element for $40, same problem. Replaced the thermostat $15 and controller board $150 at same time, bingo problem solved. Had to defrost with the hair dryer each time, biggest pain. Had an issue finding a Utube that showed the water filter system and thermistor removal for this model, otherwise straightforward, but not a 30 minute job.

The new bin arrived, I slid it in place and away we went.

I ordered 3 items based on my model and serial number from the website.

door handle off but 2 screws top and bottom of handle that attach to door remained under top and bottom molding. had to remove molding which was tricky. Held onto door with plastic clips which several broke when trying to get molding off. Figured out I had to tap top molding up to remove. unscrewed pieces of door handle and attached new handle. Had to use contact cement to secure molding to door where clips had broken.

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

removed ice maker box and disassembled crusher unit on front of box and installed new housing.