CPFFC350 Porter Cable Nailer - Overview
Models starting with CPFFC350
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Bushing Strain Relief
PartSelect #: PS12402238
Manufacturer #: 33821-00
This is a genuine OEM sourced component which is specially designed for use with air compressors. A strain relief is designed to slide onto your cord and fit securely at the end, where it's firm rubbe...
$7.44
Special Order
Pressure Switch (4 Port)
PartSelect #: PS11874353
Manufacturer #: 5140122-77
This item is an original part from Porter Cable for use in compressors. The pressure switch is made out of durable materials. You may need a screwdriver and a wrench set when replacing this item. Over...
No Longer Available
DRAIN VALVE
PartSelect #: PS12508562
Manufacturer #: N286039
When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where ...
$12.20
In Stock
Order within the next 54 mins and your part ships today!
ASSY FASTENER
PartSelect #: PS12512819
Manufacturer #: ACG-408
This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to ...
$7.44
Special Order
Common Symptoms of models starting with CPFFC350
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The air was bypassing the compressor gaskets and cylinder wall was worn out
1 remove cover
2 unhook air line to tank
3 remove head bolts
4 remove intake from head
5 remove flywheel bolt to free up pump piston
6 remove screw on top of piston to change out gasket
7 remove the cylinder sleeve install piston from the top
8 reassemble piston rod end and the flywheel
9 on the head cover are two gaskets one on top and one on the bottom head
10 insert intake piece and bolt the head cover back in place
11 reinstall the air line and unit cover and secure with three cover screws
2 unhook air line to tank
3 remove head bolts
4 remove intake from head
5 remove flywheel bolt to free up pump piston
6 remove screw on top of piston to change out gasket
7 remove the cylinder sleeve install piston from the top
8 reassemble piston rod end and the flywheel
9 on the head cover are two gaskets one on top and one on the bottom head
10 insert intake piece and bolt the head cover back in place
11 reinstall the air line and unit cover and secure with three cover screws
Parts Used:
-
Charles from GARRISON, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
18 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Can't find this special screw used on many housings etc
Actually don't like using Torx bits because they are hard to center deep in the channel. I had misplaced these forcing me to order replacements.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called AGC-408 by craftsman.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called AGC-408 by craftsman.
Parts Used:
-
Tim from Tucson, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!