CLCE900FW1 Crosley Washer Dryer Combo - Instructions

Had to replace one Spring on top of the tub and both shock absorbers. Anyone with even a limited amount of mechanical ability could handle this repair. Save yourself about $300 in repair cost and replace these items yourself. Spring and Shocks absorber kit cost less than $60 with shipping.

Just look at the diagram that comes with the parts, it's a piece of cake. The most difficult part is replacing the spring, she is stiff. You will need to take the top of the machine off, which is super easy, and remove the metal keeper on top of the frame rail. Get someone to help you as you will need to lift the tub and slip the spring over the frame rail.

The shocks are the easiest part of the repair, and should take less than five mins. to replace.

disconnected electric and water supply. removed back cover from front loading washer. removed two screws from spring end plate on the top of the washer. replaced old spring with new spring/insulators by lifting the tub and hooking the new spring on. replaced the back cover and top spring cover plate. reconnected water supply and electric. machine is working like it did before the spring broke. very easy fix. the majority of the effort was moving the washer around to get easy access.

Unplug, lift top, unplug 5 wires, remove 2 screws, pull dryer front away while supporting drum. Remove old glides, snap in new. Reverse disassembly procedure

Removed old filter, installed new filter

I removed the front access panel above the washer and removed the top dryer front panel. Then pulled out the drum and noticed the drum support ball stud had broken off, rather than order a new one, I welded it back on with a mig welder. I then replaced the drum support bearing and reinstalled the drum. I then installed the new belt before placing the front top panel in place. I removed the small vented panel on the back side to access the belt tensioner and fit the belt around the pulley and motor shaft. The whole job took less than an hour.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door lock in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.

Pulled the back off and it was right there. Hardest part was to get the belt all the way around the drive wheel on the washer tub. Found out that it wasn't just the belt. It is the shock absorbers that probably broke the belt, even though the belt was probably well over 15 years old. The bouncing and banging because of the absorbers being bad probably had something to do with the belt eventually breaking. Now, we need to replace the shock absorbers.A big thing to remember about the belt install....clean the drive wheel real good!!!

The tub is supported by two springs and two shock absorbers. First remove the back panel of the washer. Then I placed the auto jack from my car under the tub, alongside the motor, and cranked it up, lifting the tub, until the top of the seal in the front was compressed. Then I took the top off of the washer to access the springs. There are retaining straps over the top of each spring that I had to remove to get to the springs. Pulling up hard on the spring allowed me to get a pair of pliers on the spring and pull it out of the slot it was in.

Once it was out of the slot I could remove it from the tub as well. I put the new spring in and replaced the retaining strap. Then I repeated this process on the other spring.

Once both springs were in place the tub was hanging as it should and the seal around the door was smooth all the way around. I haven't seen any more leaks since replacing the springs.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

screwed in the new legs and leveled it off again.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

While my wife was using the dryer, she noticed a loud sound and sparks coming from the bottom of the dryer (and an elctrical smell). The dryer stopped heating. When I started taking off the top and front of the dryer, I noticed what looked like a thermostat had melted and burned. I called a local part store and they said they would have to order it and it would take two weeks. But the guy was kind enough to give me the part number and told me to call anothe store. Instead I went online, found this site and the next day I had the part. It took me less than an hour to install it and reassemble the dryer. Me and my wife were very pleased.

First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.