CGS3760ADB Magic Chef Range Parts and Repair Help
Models > CGS3760ADB

CGS3760ADB Magic Chef Range - Overview

Find Parts and Repair Help for CGS3760ADB.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(10)
PartSelect #: PS884734
Manufacturer #: 8009
This replacement light bulb is sold individually.
CAD$5.93
In Stock
(6)
PartSelect #: PS2085070
Manufacturer #: 74007498
This broil igniter assembly comes with its own metallic mounting bracket and an seven inch long dual wire lead with a plastic plug.
CAD$59.42
In Stock
(7)
PartSelect #: PS2003225
Manufacturer #: 12001655
This temperature sensor detects the temperature within the oven cavity.
CAD$37.95
In Stock
(5)
PartSelect #: PS2082000
Manufacturer #: 74004053
This top burner igniter comes with a mounting bracket.
CAD$51.97
In Stock
(3)
PartSelect #: PS11744009
Manufacturer #: WP74002557
This leveling leg is approximately two inches long. It is black in color and is made entirely of plastic.
CAD$7.88
In Stock
(3)
PartSelect #: PS11742743
Manufacturer #: WP489355
This screw is sold individually.
CAD$6.79
In Stock
(8)
PartSelect #: PS11749287
Manufacturer #: WPW10162384
This oven door gasket comes with built in retaining clips.
CAD$59.51
In Stock
(1)
PartSelect #: PS11741732
Manufacturer #: WP3412D024-09
This is a black burner head with the spark electrode. NOTE: This part has been updated and there is no longer a gasket seal required.
CAD$67.23
In Stock
(3)
PartSelect #: PS11744745
Manufacturer #: WP7801P173-60
Used in the lower oven. Sold individually.
CAD$79.07
In Stock
(1)
PartSelect #: PS2003113
Manufacturer #: 12001527
This wheel and shaft is used to open and close the bottom storage drawer of a range/stove.
CAD$7.66
On Order
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn’t heat up properly

  • Customer: James from Berwick, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 232 of 257 people found this instruction helpful
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read ... read more

F1 code - gas over would not heat.

Short Oven Sensor Kit – Part Number: 12001655
  • Customer: george from birmingham, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 156 of 167 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was ... read more

gas burner ignitor failure

Top Burner Igniter – Part Number: 74004053
  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 132 of 146 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more