CGS1750ADH Magic Chef Range - Instructions

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.

The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.

Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  tool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry

TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pushed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.

If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.

The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

replaced heat sensor

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same