Models
>
CGR3742CDC
CGR3742CDC Magic Chef Range - Overview
Sections of the CGR3742CDC
[Viewing 7 of 7]Manuals & Care Guides for CGR3742CDC
Click to downloadKeep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$37.19
In Stock
Order within the next 6 hrs and your part ships today!
Oven Igniter - Vertical Mount Bake and Broil
PartSelect #: PS2085070
Manufacturer #: 74007498
This broil igniter assembly comes with its own metallic mounting bracket and an seven inch long dual wire lead with a plastic plug.
$118.60
In Stock
Order within the next 6 hrs and your part ships today!
Short Oven Sensor Kit
PartSelect #: PS2003225
Manufacturer #: 12001655
This temperature sensor detects the temperature within the oven cavity.
$58.89
In Stock
Order within the next 6 hrs and your part ships today!
LEVELER-FOOT,SCREW,F/S,NYLON
PartSelect #: PS16875974
Manufacturer #: W11665456
This leveling leg is two inches long. It is all black in color and it is made entirely of plastic.
$26.92
In Stock
Order within the next 6 hrs and your part ships today!
Top Burner Igniter
PartSelect #: PS2082000
Manufacturer #: 74004053
This top burner igniter comes with a mounting bracket.
$52.27
In Stock
Order within the next 6 hrs and your part ships today!
Door Gasket
PartSelect #: PS11749287
Manufacturer #: WPW10162384
This oven door gasket comes with built in retaining clips.
$118.08
In Stock
Order within the next 6 hrs and your part ships today!
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.43
In Stock
Order within the next 6 hrs and your part ships today!
Screw with Washer
PartSelect #: PS11744138
Manufacturer #: WP74006515
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven...
$10.11
In Stock
Order within the next 6 hrs and your part ships today!
Oven Rack
PartSelect #: PS11744745
Manufacturer #: WP7801P173-60
Used in the lower oven. Sold individually.
$122.69
In Stock
Order within the next 6 hrs and your part ships today!
Screw
PartSelect #: PS11753384
Manufacturer #: WPW10348409
Sold individually.
$9.86
In Stock
Order within the next 6 hrs and your part ships today!
Door Hinge - Left or Right Side
PartSelect #: PS11744424
Manufacturer #: WP74011141
This hinge can be used for either the left or the right side of the oven door. Sold individually.
$132.48
In Stock
Order within the next 6 hrs and your part ships today!
Drawer Wheel
PartSelect #: PS11744052
Manufacturer #: WP74004078
This wheel is used to guide the bottom drawer on a oven/stove.
$18.03
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for CGR3742CDC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CGR3742CDC
[Viewing 10 of 10]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn’t heat up properly
My oven has two igniters so I needed to determine which one was the problem.
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Good luck.
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Good luck.
Parts Used:
-
James from Berwick, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
246 of 279 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1 code - gas over would not heat.
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Parts Used:
-
george from birmingham, AL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
171 of 183 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Parts Used:
-
roy from East Providence, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
140 of 158 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!