CGLMV168KS003 General Electric Range - Instructions

Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.

Unpugged microwave. Removed the screws on the bottom cover of the micorwave. Unpugged drive motor and removed two screws from drive motor. Installed new motor and replaced the bottom cover, plugged in microwave . . . presto!

Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.

Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.

Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.

It functioned good as new. Relatively cheap and very easy fix.

Open the door. Pry out the plastic cover shield to expose the bottom screw. Remove the screws and the remains of the broken handle. Install the new handle. Reinstall the cover.

Piece of cake!

got instructions from this site . Removed top grill with two screws and lifted the door off. Using the putty knife and small screwdriver pried off the inner surround, from the outer edge, not the inner edge. Two screws for the handle were apparent, removed them. Then found the latches holding the inner glass frame ,released them and removed. Next removed the remaining two screws for the handle, the handle could then be put on the new door frame. Good time to clean everything, then reversed steps and reassembled and mounted door. Recommend a quick study of the new outer door frame to find latches and tabs and such to assist in removal of the parts.

We removed the top vent panel and the door lifted right off. The hardest part was figuring out how to get the handle off the door. The web has easy to follow instructions so we got the inner plastic seal removed and all the screws were exposed for the handle. Once the handle was off, we pryed the melted part out of the door frame and replaced it, after cleaning the glass on both sides. Once replaced, the oven looked new again. We spent $60 for the part, rather than $450 for a new oven!

Ordered a replacement grill, replaced the optional charcoal filter at the same time. Took just a little effort to get the alignment tabs in place--required just a little more elbow grease than you'd think, then replaced the two screws.

Followed instructions listed here that I needed to separate the inside facing on the door with a butter knife so that I could see the two screws that held the handle in place. Easy off, easy on. And I am NOT a very good handy man.

Gently remove the interior trim with a putty knife. Remove the two screws holding the old handle in place. Replace the new door handle. Screw the new handle in place. Align the trim and snap it back in place. Confirm the door handle is secure. I applied a little Gorilla Glue to the new handle for added strength before screwing it on.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

Open micro owen door. With a spatula(or knife) remove the plastic ban around the glass . It will pop out without any problem. Then remove old parts, save the screws(None given with the spare part), Adjust the new handle and put the screws. The secret is the removal of the plastic around the window Then an easy job...

getting the frame on was fairly easy, used a flat knife(butter) to loosen up and flip off, mostly over the notch in the hinge part. the handle did not fit, correctly upon and broke the screw area for securing, and had to order another handle, did not fit with the new frame, only one hole lined up. used the only two screws to that lined up, hopefully will hold good enough