Models > CGLGF382DSG > Instructions

CGLGF382DSG Frigidaire Range - Instructions

All Instructions for the CGLGF382DSG
46 - 60 of 98
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The igniter won't work
On the front left burner would not ignite, after the installation of the new one, same problem, new one didn't fix.. I guess it's something with the electric igniter
Parts Used:
Front Burner Igniter/Orifice Assembly
  • Bobby from FORT DEFIANCE, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F10 code going off
Went well, and working thank you ??
Parts Used:
Temperature Sensor
  • edward from BRISTOL, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
run away temp
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.
Parts Used:
Temperature Sensor
  • James from ELKHORN, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wasn’t heating
Used instruction video & replaced part.
Parts Used:
Temperature Sensor
  • Felicia from FORT MILL, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter failing to energize even though there was 120 volts being supplied.
Slide Range away from wall, unplug Range, remove rear cover (4) screws, removed burner assembly (5) screws, unplugged Igniter connector, loosen Igniter bracket, remove Igniter (2) screws. Reverse process to install new Igniter. I also wore latex gloves to prevent touching graphite portion of Igniter. Tested Broiler for operation, slid Range back into position. All good.
Parts Used:
IGNITOR KIT, HALF SHEILD
  • Richard from MERCERVILLE, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken oven door cap.
Watched a video - piece of cake!
Parts Used:
Oven Door Cap - White
  • James from LAKEWOOD, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat or sometimes hold heat to set temp
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.
Parts Used:
Temperature Sensor
  • TRACY from NEW PHILA, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced theoriginal power cord.
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Parts Used:
CORD
  • Blanca from Union City, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace igniter
New part needed to be spliced to old connector with porcelain wire nuts then removed lower oven drawer to access the connection for igniter
Parts Used:
IGNITOR KIT, HALF SHEILD
  • Edward from NORWOOD, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven temperature was not consistent.
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Parts Used:
Temperature Sensor
  • Kimberly from OWASSO, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would sporadically light when initially turned on
Watched the you tube video from this website and did the same to my own oven. Much better replacement igniter than was installed in oven from factory and amazing packaging from partselect.com. Thank you!
Parts Used:
Bake Igniter
  • Jessica from PITTSBURGH, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven bottom panel
Unscrewed old panel/removed and inserting new panel and used same 2 screws to secure in place.
Parts Used:
Panel
  • Maria from NEW ORLEANS, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
temp. probe
Easy watched on line video
Parts Used:
Temperature Sensor
  • Deane from WINCHESTER, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range displayed error code F10
Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
Parts Used:
Temperature Sensor
  • Timothy from Palm City, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven was over heating temp. of oven keep climbing
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Parts Used:
Temperature Sensor
  • Herbert from MARIETTA, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CGLGF382DSG
46 - 60 of 98
Back to Top