All Installation Instructions for General Electric Dryer CGL2000RW169

Dryer was making a loud squealing noise.

I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Patrick from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No Heat

Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.

Parts Used:

Dryer Igniter

Steve from Santa Ana, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Previous nob cracked

The shaft of the previous nob had cracked and even super glue would not hold it together. The dryer timer could no longer be set without it. Slipped it off and slipped on the new one and it worked perfectly.

Parts Used:

Timer Knob

Gabrielle from CONYERS, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rubbing noise while dryer was running

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Carol from Simpsonville, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No heat from dryer. Diagnosed by others as the Gas Valve

Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.

Parts Used:

2-Coil Gas Shut-Off Valve Assembly

William from Deerfield, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Loud squeaking

Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

DRYER FRONT BEARING WHITE 2PK

Robert from BALTIMORE, MD
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Timer was stripped

Just placed it where it belonged.

Parts Used:

Timer Knob

Mary Ann from Buzzards Bay, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Switch not working.

Open the door and removed the part. Installed the new part and started the dryer.

Parts Used:

Door Switch

Alan from BELFORD, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace knob

No brainer

Parts Used:

Timer Knob

Dave from DOUGLAS, WY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The old dryer knob broke

I took off the old dryer knob and put on the new one

Parts Used:

Timer Knob

Charlie from KILGORE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No power to dishwasher

Replace both micro switches.

Parts Used:

Interlock Switch

Robert from OLD TOWN, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Timer Knob

Very repair just put new on and it worked great

Parts Used:

Timer Knob

Sharon from FARMERVILLE, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Loud squeek when dryer was running

Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Clarke from Grapevine, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I had to convert from natural gas to liquid propane

My son is an engineer and repairs washers and dryers for a large commercial laundry company on a daily basis. He installed my part easily and had me up and running in no time.

Parts Used: