CGEF3055MFE Frigidaire Range - Instructions

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.

Followed the instructions that came with control board. The new contol kit came with a upgrade, which I think to help keep this from happening again. Very easy repair to do.

Unplugged unit and removed back panel with nut driver. Removed door, racks and unscrewed element braces from back of unit. Removed element and installed the new one. Reversed the process and then ran the unit through a preheat cycle to test it.

Twisted replacement bulb into place easily. Let there be light!

Replaced the dual element switch and that fixed it up

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

My husband followed the video instructions and it was easy to fix.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Open oven door completely. Release hinge locks by prying top of tabs at hinge. Close door halfway, lift stright up about 1/2", and away at 45 degree angle to remove entire door from hinges. Set door on blanket on floor with front facing down. With Phillips screwdriver, remove top two screws holding handle. Set handle aside. At bottom edge, remove four Phillip's screws. You can now separate the outer door shell from the inner door. Clean out any remaining glass. Tip: This is a great time to clean inner glass of any grease or other liquid that may have gotten between the glasses. Set new glass in place with foil at top facing up and slide fully to the bottom of the outer door. Reattach the inner door to the outer shell with the four bottom screws and the top two handle screws. Tip: Get handle screws started, but do not tighten until all four bottom screws are started. Snug but do not overtighten. That's all there is to it. Re-insert door hinges into slots on oven frame and push down to seat. Engage hinge locks and close door slowly to make sure hinges are seated properly. My wife did this by herself in less than 30 minutes while I walked her through it.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

removed the old burner and put the new one in it's place.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.