All Installation Instructions for Frigidaire Range CGCS389FS1

door latch motor not working

remove oven door, disassemble front of glass top range then basically
it was just plug and play then reassemble be careful oven door is heavy

Parts Used:

Door Latch Motor & Switch Assembly

Daniel from REYNOLDSBURG, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

light bilb went out

replaced it

Parts Used:

Light Bulb

Denise from Landover, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

No Power to the Oven

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Parts Used:

Main Terminal Block Kit

Tony from Hartford, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Lens cover for oven light broke.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Parts Used:

LENS

Amy from Corona, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Convection fan making noise

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

Parts Used:

Convection Fan Motor

Willis from Friendsville, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The screw head was stripped and couldn't be extracted with a Phillips head screwdriver

If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damaged screw and then installed the replacement. Wish all appliance repairs were this easy!

Parts Used:

Oven Door Handle Mounting Screw

Robert from GLEN BURNIE, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Two of theTop gas burners would not spark

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

Parts Used:

MODULE

Robert R from Lewistown, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Parts Used:

Main Terminal Block Kit

Sue from Lampasas, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

Parts Used:

LENS

Light Bulb

Sharon from Foley, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Parts Used:

Temperature Sensor

Robert from Glasgow, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Uneven bake temperature

I removed the element, plugged in the new one and that has corrected the uneven oven temperature.

Parts Used:

Bake Element - 3400W

Jim from Franklin, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Oven would not reach temperature

Husband made install in very short time. Nice to have them back in operation.

Parts Used:

Door Seal

Temperature Sensor

Sandra from Magnolia, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

really bad ugly streaks inside of glass

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Parts Used: