CFHT1814LZ0 Frigidaire Refrigerator - Instructions

At first I tried to insall the new gasket with the door still attached to the refrigerator. It was difficult to assure that the bottom of the gasket was properly installed at the bottom. As a result I removed the door from the refrigerator, finished installing the gasket and then put the door back on the refrigerator

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Removed screws. Rotate door handle, and slide it off anchor screw. Slide new door handle on anchor screw, and rotate door handle into position. Replace screws.

Bought a new
capacitor.

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

Rack door slid into place easily. Repair required no tools and took maybe 20 seconds to install!
Very easy job!

YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.

The fit was good even though the top retainer bar seems to be a tighter more secure fit than the middle retainer bar.The retainer bars are made to simply snap into place. Great to receive these replacement shelf retainer bars. Thanks!!

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Went pretty straight forward, except the heat shrink tubing was about 2 sizes too big. Would not shrink small enough to seal the connections. Even with a heat gun it would not shrink small enough. OH, another think is when I plugged the fridge back in the defrost timer was in defrost mode. Took me a few minutes to figure that out and use a screwdriver to turn the timer back to the on position. Other than that, install was pretty simple.

Parts arrived, my son brought the box into the home we first had to take all the food and stuff out of the fridge washed her down made the inside and outside look brand new. (1st) piece replace was the Door Gasket, I couldn't find a flat head screw driver so I used a butter knife and popped out the old Door Gasket cleaned away any gook and grim (Use a mister Clean Magic Eraser) They do a fantastic job. and also they get into those deep hard to reach areas. pop the new one in and that was that. New Door Gasket went right in. The (2nd) Door Retainer bars. they pop off really easy you can hit them with the bottom of you hand and they com right off, got one correct. had to switch the other two around as the door didn't close at first than door closed without a problem in fact it came with an extra (Door Retainer Bar) one so thanks the fridge has an extra should one break. (3rd) the crisper and fresh baskets. scrubs the heck out of the shelf and the glass. those look brand new. and then when dry put everything in added the baskets to were they go fridge looks brand new and we have gotten a whole new skill set. this was a very easy project to do and it was a lot of fun. I hope your will go as smoothly.

Took old handle off . Then slipped new one on bottem in place @ top placed screws in place .Very easy .

We took off the broken bar and put on the new one. It clips on. Took about 10 seconds and could have been done by a 5 year old.

Took old gasket off and put new gasket into place. Part came in the mail in 2 days. Hardest part was finding the model number of the refrigerator.