All Installation Instructions for Frigidaire Range CFGF366FCC

oven bottom had foil stuck on it would not come off

First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in

Parts Used:

Panel

ronald from brownsburg, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

15 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The burner knobs were lose and kept falling off.

Pull off the old knob, and slide the new knob into place. Less than 10 seconds for each knob.

Parts Used:

Top Burner Knob

J Andrew from Richmond, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

13 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Regulator had propane leak past diaphragm

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

Parts Used:

REGULATOR

Albern from Bainbridge IS., WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench set

14 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven would not ignite, gas smell, igniter glows

Disconnected power, I removed the igniter from oven. Measured the resistance (275 ohms) and then the current draw. DO NOT ATTEMPT THIS UNLESS YOU ARE ABLE TO ACCOMPLISH THIS SAFELY. I made a harness and connected the old igniter to 110 V ac, Current draw thru the meter settled at 2.7 Amps. Too weak to fully open gas valve. Valve requires 3.2 - 3.6 amps to fully operate properly. New igniter measured 300 ohms and current draw was 3.4 amps. Installed new part and everything works fine. Correct part and good service from this site

Parts Used:

IGNITOR,BAKE

John from PORT JEFF STA, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set

11 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Right front ignitor would not light

Removed grates and range cover, unscrewed all sheet metal screws and removed cover plate. Disconnect electrical connector and then removed old ignitor/orifice ass and replaced it with the new one. Replaced all screws in cover plate and then reattached range cover and grates. Turned on the gas and it lit after a few sparks took place.

Parts Used:

Front Burner Igniter/Orifice Assembly - 14K

Terry from Acton, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

12 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken Door Trim

The top of the door trim broke causing the side and glass to be loose. Easy fix by removing the broken trim and installing the new one.

Approximately 2 minutes to replace.

Parts Used:

Door Top Trim

John from Hummelstown, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

11 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

lost the metal clip inside the knob. so knob was loose

I compaed price at different sites and partselect .com was 30% cheaper for the same item. I received the part in 2 days by fed-ex.
Doing the job was real easy.Just pull the old knob out and put the new one in.

Parts Used:

Top Burner Knob

Jacob from Farmingdale, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken ceramic burner element

Simple: remove the element by hand and replace new one.

I can't believe how quickly I received my new part -literally next day.

Parts Used:

Sealed Burner Head - 14k

Phillip from Saint Simons Island, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven light stayed on & smelled like electrical burning.

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Parts Used:

Oven Door Light Switch

Vincent from Brunswick, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

16 of 35 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven light bulb went dark; it needed replacing

Twisted replacement bulb into place easily. Let there be light!

Parts Used:

Light Bulb

Lise from CEDAR GROVE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

10 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Cosmetic (dent from falling object)

Removed all burner covers/flame diverters. Slid range out from wall/cabinet. Removed 2 screws from each burner that attach to top (8 in all). Top was then easy to remove, as it just stays in place by snapping on to range, once 8 screws are removed (2 from each burner).

Parts Used:

Cooktop - Black

Gerald from Spokane, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refrigerator Light bulb went out

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Parts Used:

Light Bulb

ANGELA from MEBANE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken lens over oven light

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Parts Used:

LENS

Leslie from Warsaw, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The bolts holding the readburner were rusted and broke

The range top had to be taken off along with the front panel to get access to the place the burner pipe connects. It took more time to unassemble and assemble the range than repacing the burner. The only issue was that the burner was sent without the bolts that will hold it in place so I had to go to local hardware store to get appropriate bolts.

Parts Used: