CFGF337GSE Frigidaire Range - Instructions

It was a replace racks not repair. No problem

1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.

2. If possible, remove the storage drawer for ease of access.

3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.

4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.

5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.

6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.

7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.

8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.

9. Reattach the drawer if necessary and plug the range back in.

10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.

turn the gas off unplugged it form electric removed the line took the flame plate off removed burner tube and the screw out with a nut driver that was all just put it back in reverse

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.

It helps to remove the bottom drawer completely to gain easier access.

After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down and I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

I followed the instructions given pretty much, however none of them mentioned one important point.To remove the cover plate, do NOT try to pry it away from the unit. It will crack. Fortunately I caught it in time.I then started in another corner by inserting a razor knife between the face plate and unit and sliding it around all four sides. There was enough goo left on the plate to enable me to affix it to the new unit.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

6 screws to remove upper back panel, 4 screws to remove control. Unplug wire harness. Carefully remove adhesive backed front display cover & press to new control, & reverse process to reinstall. Exact original replacement part, quick delivery! replacement

I didn’t follow the instructions for the igniter
I simply jerked hard on the bottom drawer & it cam out onto the floor . Pulled range out & changed the oven sensor with a nut driver.
Same for the controller, 5 screws with a nut driver to remove back plate & 4 screws holding the controller in place , used the old face plate and it was easy as pie

My gas oven is an older model Frigidaire but still looks nearly new. Started having issues with it taking a long time to preheat and then losing heat rapidly when temp was reached. The control board was warped, I suspected the ignitor was faulty, so I decided to do an update of the major oven parts. The parts were substantially more economical than a repair call and diagnosis. I've never done this type of DIY repair before but after watching the videos and seeing the other reviews, I decided to tackle the job myself. I replaced the temp-probe, control panel and a new overlay along with a new oven igniter. The oven igniter was the most challenging, but only because the screws to get the bottom oven shield off took some muscle. Once removed, the new ignitor was fairly simple to install. I watched the videos again and then followed along step by step and successfully replaced all the parts. My oven works like new now! And just in time for the upcoming holidays. Thank you for great service and instructions! ~ Diana