All Installation Instructions for Frigidaire Wall Oven CFES367DS3

A friend shot out the front glass panel of my oven door with a BB gun!!

Just "locked" the hinges, pulled the door off. Removed the broken glass for the door. Switched the handle from the old door to the new one. thPut it back on e hinges.....viola!! new oven door glass!

Parts Used:

Inner Door Glass

Fritz R. from Carnelian Bay, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bilb went out

replaced it

Parts Used:

Light Bulb

Denise from Landover, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

had no instructions on how to remove old door hinge recepticle..

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Parts Used:

Door Hinge Receptacle

Douglas from Colrain, MA
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lens cover for oven light broke.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Parts Used:

LENS

Amy from Corona, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bad control switch for burner

Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.

Parts Used:

Surface Burner Infinite Switch Kit

Harry from Huntingtown, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Parts Used:

Main Terminal Block Kit

Sue from Lampasas, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

Parts Used:

LENS

Light Bulb

Sharon from Foley, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Parts Used:

Temperature Sensor

Robert from Glasgow, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Stove door switch was broken

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Parts Used:

Door Switch

James from Milford, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Parts Used:

Oven Bake Element

Jeffery from Union Point, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Coil melted in half.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Parts Used:

Oven Bake Element

Gerald from Artesia, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

lower oven element burned up

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Parts Used:

Oven Bake Element

Constantine from Vero Beach, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Tenet broke knob

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

Parts Used: