CFE28USHFSS General Electric Refrigerator - Instructions

replace sensor in refriger.

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.

There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine

as per video

Took set screw and allen wrench and screwed set screw into place.

Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,

After replacing the Defrost Thermostat, Defrost Heater Assembly, and the Main Board, I concluded that the problem must be the Defrost Thermistor, which I replaced in less than 10 minutes and it fixed the problem! I cut the wires on the old thermistor and connected the new one after stripping the wires and taped the new connections with electrical wire. Fast and easy repair (the last part anyway ;).

Unplugged unit and removed vented cover over compressor section. The run capacitor is a simple fix 1 Phillips head screw and 2 spade wire connectors. For the temperature sensor I had to remove all drawers and the ice maker to remove the back cover to expose the condenser. Put a bowl at the drain stem in the rear of the unit and used a heat gun to defrost the coils on the condenser. Cut the wire about 3" from the sensor end . cut about the same off the new sensor stripped the wires put shrink wrap on each wire, attached butt connecors . heat gun for the shrink wrap and reassembled everything. Simple job that took about a half hour to do both. I will monitor the fridge for a couple of weeks to see if I need to change the control board.

Easy. Followed the video instrucations. the part was right there next to the compressor.

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

First, I had to remove the freezer drawer front. This is 8 large phillips head screws. then remove the plastic cover over the drawer slides. to do this, remove the white center screw from the slide near where it attaches to the drawer front. then the plastic cover will slide off pushing to the rear of the slide. take off the slides from the freezer walls by removing the phillips screws and pulling them towards you. They have tabs/slots in the rear. remove the center tray support and support bars, too. the icemaker has to come out, that is just 2 phillips screws but you also have to disconnect the electrical connector. just squeeze the locking wings and rock/pull. a screw in the top center of the back panel comes out. Lift and pull the back panel out. The evaporator coil appears. The thermocouple is attached to the coil in the upper right. Cut that one's wires and take it out. Just cut back about an inch from the back of the thermocouple, there is not much slack. Seperate and strip the wires back about 3/8 inch. Do the same for the new thermocouple. I twisted the wires together and used a solder sleeve to join the wires. The sleeve is just a little plastic tube that has a ring of solder in it that melts with heat gun heat. You can join the wires using butt connectors or whatever method appeals to you. I just wound the extra wire and put a cable tie around it, there is plenty of hiding space in that area. Make sure the new thermocouple is contacting the coil firmly.At this point, for a test, I left everything apart, propped the drawer against the opening and plugged the fridge in. Note that the evaporator fan will not start spinning immediately! It will just sit there making little bumps like it wants to go. The temp in the coil has to get settled before the electronics in the refridge will tell the fan to spin. It takes maybe 20 minutes. Reassemble. Fridge and freezer work great. It does take several hours for all to get cold again.