CFD28SDS9 Crosley Refrigerator - Instructions

Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Unplugged frig. removed old switch with the aid of screw driver. removed wires and taped; plugged frig. back in and waited for new one. new one came, unplugged frig.removed tape from wire clips plugged in to switch and pushed switch into socket hole and plugged frig. back in; shut door, works like a new one.

problem still persists part did not fix problem. made repairs recommended per your site.

Lifted off the bad shelf and installed the new shelf. Works great just like new again.

Push in on filter and it releases pull filter out. Slide new one in push in and it locks it. Run water for 2 minutes and it is finished

it is a very simple process. pull out the water filter. put in the new one after removing the plastic tops. slide the filter in place pushing to set it in place. run water through water spout on door of fridge for about 3 minutes or until all the air bubbles are out. and there you are ready for a drink of water.

Removed new replacement crisper from packaging. Washed crisper in warm soapy water. Rinsed & dried crisper. Aligned crisper drawer with tracks on crisper shelf and slid crisper in until front panel was in home position. Slid crisper full travel in & out a couple of times to check not only for correct travel but also travel stops. Adjusted crisper setting, placed produce into crisper, closed crisper, & closed refrigerator. WARNING do not slam, drop, or otherwise mishandle crisper. It's only plastic!

Once the filter arrived, I pushed it in that releases a latch and removed the clogged filter. I then pushed in the new filter and when it clicked, I ran a few cups of water through it to clear any debris left from manufacturing and the job was finished. Less than 15 minutes.

Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.

Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.