CFD28SDS1 Crosley Refrigerator - Instructions

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.

After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you

i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.

Basically unhooked water lines and removed the screws

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Easy repair. Great part. The hardest part was removing the fridge lower exterior door so I could get access to the icemaker. A couple of youtube videos later I realized loosen a screw, slide the icemaker out and unplug slide the new icemaker in and plug-in making sure the water spout was accurately over the water receptacle for the icemaker. Several hours later I was up to my eyeballs in beautiful clear ice cubes. Highly recommend.

Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.

Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

We replaced the damper, but it didn't fix the problem. We then purchased and replaced the thermistor. (We had previously replaced the defrost thermostat). The refrigerator side is now cooling better, but not enough. The damper doesn't seem to be opening. So we have now unplugged the damper and left the opening between the refrigerator propped open and the refrigerator side is now cool enough. (We had previously tried keeping the damper open before we replaced the thermistor and the refrigerator didn't cool off. So the thermistor did fix something, but the damper doesn't seem to have been the problem).

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

slid shelf out, slid new bin in.1 2 3