CEW30DF6GSE Electrolux Range - Instructions

First had to determine what was the source of the problem. Removed the back panel to expose the heating element connections. Cycled thru the different oven settings; bake, convection bake, roast. convection roast and broil, while checking the voltage on the 3 heating elements; upper, convection and lower elements. As the oven cycled thru the different temperature settings the volt meter showed that the lower element would not shut down when set temperature was met. Checking the wiring diagram showed that the culprit was probably that the lower element relay in the relay panel was not cycling as required. Decided that replacing the relay panel would fix the problem, and it did. Replacement of the relay panel was very easy and the PartsSelect part was the exact part required.

I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

Oven is working great now.

Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

Thanks

Went well, and working thank you ??

Used instruction video & replaced part.

first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!

Went online to find replacement rack. Didn't want to spend the money for a rack I didn't like. Besides the range is 11 years old. Still in great shape. Opted for the simple oven rack.
Open the box and place in oven. Wah lah..
Thank you partselect.com

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.