Models > CES365HZ1 > Instructions

CES365HZ1 Whirlpool Range - Instructions

All Instructions for the CES365HZ1
106 - 120 of 215
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bake element out
use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.
Parts Used:
Oven Bake Element
  • Joyce from BALLWIN, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bunner was not shuting off automaticly
I used the replacement video from the web site. The replacement went great.
Parts Used:
Surface Burner Element Switch, Large Burner
  • Lee from GROVE CITY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I decided it was the switch that was bad as it would not turn on or anything.
After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.
Parts Used:
Surface Burner Element Switch, Large Burner
  • Christy from OROFINO, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my first order a small drip bowl
came only I had to order the set again
Parts Used:
Drip Bowl Kit - Light Gray
  • marie from WATERBURY, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element had burned out, and the drawer glides were broken .
Replaced both .
Parts Used:
Oven Bake Element Range Rear Drawer Glide
  • Allen from ASHLAND, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
Parts Used:
Broil Element
  • PHILIP from NORTH PORT, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven heating coil snapped and would no longer heat.
It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!
Parts Used:
Range Receptacle Kit
  • Diane from Gillett, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
Parts Used:
Oven Bake Element
  • Jenny from GREENFIELD, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Service Elements Didn't Work (Didn't heat up)
Unplugged old elements and plugged in new ones
Parts Used:
Range Surface Element Standard Y-Frame Range Surface Burner
  • Roseann from MEADVILLE, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes would not fully dry in automatic cycle
1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Parts Used:
Range Door Hinge Left Or Right Side
  • Robert from WALDORF, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke drawer bracket
Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!
Parts Used:
Range Front Drawer Glide
  • Valerie from ROCHESTER, MN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat up.
Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.
Parts Used:
Oven Bake Element
  • Johnie from PARKERSBURG, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Demon Possession
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Parts Used:
Broil Element
  • Kevin from Greensboro, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Elementwas burnt into
Watched the video and did as shown
Parts Used:
Oven Bake Element
  • Fred from APACHE JCT, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
Parts Used:
Hinge Pin Kit
  • Mary from LARAMIE, WY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CES365HZ1
106 - 120 of 215
Back to Top