CDU650AWB Crosley Dishwasher - Instructions

If you have already figured out what the problem and the part number is, and have gotten this far, then you probably already know how to fix it and do not need instructions. But if you do, I took the following steps:

1) Use a #T20 star bit to remove the screws from the inner door panel. [Note: I would use a manual screw driver as opposed to a drill/driver, because you are less likely to accidentally strip the threads in the screw holes];

2) Lift the panel up and detach the wire harnesses from the metal receptacles attached to the old assembly.

3) Remove the old latch assembly, and then press the wire harnesses into the metal receptacles on the new assembly. [Note: You may have trouble getting the wiring harnesses out. If you pull hard enough you can get them off, but if you truly cannot, simply detach the metal receptacles from both the new and old latch assemblies and place the old metal receptacles on the new assembly with the wire harnesses still attached. If you choose this method, be careful with the little plastic retainer bars that secure the metal receptacles, they are pretty easy to break.];

3) Put the new latch assembly in its seating and re-secure the inner door panel. If you used a drill/driver before, I would really switch to a manual driver at this point.

4) Take the dishes out of your bathtub, and place them in the dishwasher.

5) Close the door back.

6) Stare.

Disconnect the power,open panel and remove screws with the exception of the two bottom ones. This allows the panel cover to be opened far enough to pull latch assembly clear.
Remove electrical contacts (2) and put defective unit aside. Connect new latch unit to both wire saddles,line up unit with proper holes and install two screws. Once fixed in place,install all other screws and switch power back on.Do a short test run to check for any leaks

Removed filter cover and filter and found the plastic chopper sleeve was stripped out. Followed instructions that came with the seal kit to replace it.

I removed the old rack adjuster by unscrewing four screws. I put the new rack adjuster in place, carefully fitted the adjustment parts together, then replaced the four screws. The best part of the repair was that Parts Select had originally indicated that my part would be on back order for a few weeks, but I actually received the part within just a few days. What a nice surprise - thanks!

Replaced the door gasket, inner foam strip and the bottom seals on the door. Unfortunately I broke the plastic door latch handle in the process and had to purchase a complete latch assembly too.

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Received the entire latch/switch assembly rather than just the plastic latch handle. This was a pleasant surprise, especially for the price. The latch assembly was clearly a better designed and more robust assembly than the original.
Removed the inside panel of the door by removing the dozen or so TORX screws.
Pulled the inside panel away from the outside door panel (gently, cables attached) to gain access to the latch/switch assembly. A second set of hands was helpful for this and some following steps.
At that point the latch assembly was free mechanically from the door, but there were two wiring harnesses attached to the latch assembly via plug connectors to the two microswitches on the latch assembly. It looked like it was going to be easy to unplug the harness from the switches, but I could not do it. Never did figure out how to do it.
Removed the two microswitches (with harnesses attached) from the 'old' latch assembly by pulling back the plastic tab that holds each switch in place. At that point the rest of the latch assembly was completely free from the machine.
Removed the two microswitches from the 'new' latch assembly using the same method as above. This step requires care as the plastic parts and switches can be damaged.
Put in place the two 'old' microswitches with wiring harnesses attached on each side of the 'new' latch assembly. These snap in place. This requires care, as above, and the second set of hands to hold away the inside door panel.
Put the latch/switch assembly in place in the door, and put the inside door panel back in place.
Re-installed the TORX screws holding the inside door panel - and latch assembly - to the door.
I kept the 'new' microswitches because one day the 'old' switches may fail. If that happens and I want to replace the microswitches, I still don't know how I will remove the switches from the wiring harness. I guess I'll figure that out if the time comes.
Except for the difficulties disconnecting the microswitches from the harnesses, this was an easy and straightforward job. The latching of the door seems more positive, now, and the machine is working fine.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

Basically took out of box and put in dishwasher.

Door gasket fit in like a champ! No special tools required - just scissors to trim off the excess ends. Unfortunately this didn't correct the leak. The leak was caused by a Home Inspector who ran the dishwasher without soap. The soap has a defoamer in it. If you run the dishwasher without soap the water mixes with the surfactant in the jet dry and causes foam which results in a door leak. The foam also causes the pump to cavitate which is not healthy for the pump.

A common theme you'll see thoughout the repair stories;

1. many broken handles at the hinge
2. TURN THE POWER OFF.

This assembly comes with the microswitches (which is not a bad idea to replace since they are electromechanical and will eventually fail). My only recommendation is to buy a couple of these handle assemblies because they WILL fail. I'm on my 3rd!

I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.

Removed 11 T20 Torx head screws. Removed and replaced latch. Removed and replaced door seal and foam insulation strip - no additional tools required. Super easy to repair and didn't leak a drop afterwards.