All Installation Instructions for General Electric Range CCGS990SET4SS

knobs were worn as was the burner cap

take off old put on new. easy.

Parts Used:

Burner Knob

Burner Cap - 15K

Paul from Soquel, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

22 of 42 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom oven wouldn't warm up

Remove the door for easier access. Remove the fan cover from the back of the oven (about 6 Phillips head screws). Remove the bottom cover (2 5/16" screws). Lift the cover from the back and slide out. Remove the old igniter (2 5/16" screws). Pull the oven away from the wall. Remove back cover (3 5/16" screws). Unplug igniter, feed wiring through the oven. Install new igniter.

Parts Used:

Oven Burner Igniter

Mike from SAYREVILLE, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

13 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner grate bumpers/feet missing

Hi temp (900 deg) engine gasket adhesive on numbs and press in. DONE !

Parts Used:

Rubber Feet

Raymond from Waukegan, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

13 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven post mini explosion sounding

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Parts Used:

DEFLECTOR OVEN

Mchael J. from Chesterfield, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

13 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original burner cap was chipping; must have been dropped somewhere along the line.

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Parts Used:

Burner Cap - 15K

Mitzi from Briarcliff Manor, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

plastic on knob cracked

changed the knob to the new one. Light bulb still working-bought a new one in the event it burnout.

Parts Used:

Burner Knob

Angela from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt burner

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Parts Used:

Burner Head - Medium - 9500

Janine from Wind Gap, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed To Replace Burner

Took longer to open the box.

Parts Used:

Small Burner - 5K

Robert K from York, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

temperture

replace sensor

Parts Used:

Range Oven Temperature Sensor

mel from LOGAN, UT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hole burned through deflector oven and metal dropped onto igniter and burned it out

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Parts Used:

DEFLECTOR OVEN

Scott from ARDMORE, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The knob dial skirts are made of plastic and become warped with the heat

I had really hoped these new knob dual skirts would be made of metal and therefore superior to the ones that came with the oven, but alas, these are also made of plastic. It was easy to screw them into place although they didn’t come with screws I just used the old screws. I sure hope they last longer than the originals!

Parts Used:

Knob Dial Skirt

Nora from WINTER PARK, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Misleading ordering information: a HUSTLE

I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.

Parts Used:

Rubber Feet