CC3520SRW Crosley Range - Instructions

removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.

I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!

Easiest repair ever.

#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws

Everything took 15 mintes max.

Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)

Reversed the process.

Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.

I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!

pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.

Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PRESTO DONE

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

The burner wouldn't work. I just plugged in the new one and all was done.

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.

First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.

First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.

I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.

Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in. Plugged stove in and worked perfect.