CAQE7021LW1 Frigidaire - Instructions

When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)

I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

All the symptoms indicated the thermister (located in the exhaust air stream of the dryer) was the problem. Pulled the lower panel off the dryer. Took out the two lower screws holding the door panel on so I could pull the front panel out just enough to get a screwdriver on the screws holding the thermister on. Unhooked the two wires connected to it and hooked them to the new thermister(no need to observe polarity). Put the new thermister in, screwed the door panel back down, put the lower panel on and started drying clothes.

Unpluged the dryer, took out the light assembly, unpluged the wires to the unit, replaced the old unit with new unit from Partselect.
Plugged dryer in, problem fixed.
Taa Daa

Thanks, PARTSELECT.

That saved me about $50.00 YAHOO!!

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

spoke with repair person he indicated problem was not door switch but control board, prior to repair person arriving I receive the switch in the mail, I unplugged drier used a small edged screw driver to remove door light switch, removed three wire clips from the old switch, re connected the wires to new switch pushed the new switch into its location, closed the door light went out and the drier started and has ran just fine ever since, saved myself several hundred dollars or a new drier

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

All I did was push the new part into the machine! So easy!

Very easy lined the slots on the dryer door with the gasket and
pushed the small tabs into the slots of the gasket door with my
fingers - A $10 fix that would have probably would have been in
excess of $100 if we called a service repair person

This was the easiest repair ever done. Pulled out old seal/gasket and popped in new one. Took about 2 minutes. Be sure to mark where ends of new door seal (gasket) starts and ends when removing the old one.

EZ. Viewed you tube replacement video, EZ off and on, applied little heat, closed dryer door, good fit, heat made it fit even better

I removed the Moisture sensor from inside the dryer and installed the new one. Two wires are connected to the sensor and it is fastened down with two screws.

Watched a YouTube video. Very easy to replace, I’m 73 year old woman…this was a very easy job, anyone can do it!

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again