C2757*0 Roper Cooktop - Instructions

Fairly straight forward except for hidden 5/16 self tap screw coming from back side of heat ducting that is welded to drier. You have to remove this by feel and restart by feel which may be difficult for some. This screw holds the element to the heat duct. It has to come out

Super easy!
-unplugged
-removed the 6 screws in the rear
-pulled off the back panel
-unplugged the 2 wires attached to the heater element (note which one connects to where)
-remove dryer filter and the 2 top screws that next to it
- lifted the top up
- there is one screw at the top of the heater element casing that needed to be removed.
- poped the heater casing away from the dryer.
then pulled it out from the bottom
- removed the one screw holding the heater element in the case, and slide it out
-slide the new one in, and put the screww back in
-pushed the heater casing back up in the dryer and connected the 2 element wires.
-slide the heater casing in the 2 slots and pushed it backing to the dryer at teh top.
-screwed the on screw back in at the top of the casing.
- put the dryer top back in place and 2 fliter screws back in.
- reattached the back panel. and plugged back in.
- viola...

I followed the instructions provided by another user... worked like a champ!

Jacquie

I first disconnected the power, dryer vent hose, back panel, disconnected power leads to heater element. Next removed top screw to the heater box, slid the box up and away from lower mount. At this point I was able to remove 1 ea lower screw holding heater element in place. Removed heater element and installed new element. Put everything back in reverse order and started dryer. (Note: Be sure dryer door is closed prior to starting dryer)Yep, I screwed that up. It no "worky" when dryer door is open. Once the door was shut, it worked like a champ.

I removed the back panel and took the 2 screws out at the lint screen, lifted the top back so I could remove the bracket holding the heating element can. After this was completed I was able to remove the heating element and install the new one, I had to cut the old connectors off and wire nut the new connector together. After this part was completed I reinstaaled the heating element can, secured the top back down,reinstalled the the back panel and pluged it in and wa-la it worked. I also wanted you to know that your prices are about $ 7.00 less than a few of the other part sites I checked on line and one of the sites even said that the part I needed was no longer available. I am sure glad that I kept looking and found your site because you saved me from buying a new dryer, thank you and if I get asked where to get parts I will recommend PARTSSELECT.COM.
Fred

Located heating element at PartSelect easily.Worked perfectly

checked element leads with voltmeter (set on ohms) - no continuity. - biggest problem is that the can over the element is screwed in from the back - you have to take out the lint filter and unscrew the two screws beneath it then pry open the dryer top - then you can unscrew the one screw holding the clamp on the can. This seems to be a feature added just so people would call out for repair - I can't imagine how it would have been quicker or easier to manufacture it this way. The can just pulls out and is hinged from the bottom - you may have to jerk on it after you remove the clamp. (pull from the top). One screw holds the element in. That is it for the replacement. Now the stupid part - check to see if the exhaust vent is clogged. I pulled several cubic feet of lint out and didn't bother to put a mask on and almost choked to death. I recommend you to get a dust mask before cleaning a tube longer than 8 feet.

un plug power, pull out from wall,remove 5 screws and remove back cover. check heater element for curcuit found to be open. check the 2 temperature units on the heater housing, both ok. Remove the 2 flag connectors on the heating element, 2 wires each on temperature switches.remove upper heater case screw and bracker, lift and slide heater housing out of the dryer. Remove 1 screw holding heater element in the housing. compare old and new element, being the same. follow reverse steps and re assemble.

Turn off and unplug dryer, pull dryer away from wall to allow a decent working area. Remaoved use multi meter to assure no current flow, disconnect wires/remove at contact points. Remove panels and screwsnto expose heating element. Continue to remove screws from heating element, the only problem I had was reaching the top screw the is on the inside. I was able to squeeze my hand through an opening with a short/stubby flat head screw driver.

There are adequate repair examples in the forum especially one with the video. Pick one that you are confortable with and follow the guidelines remembering where the screws came out of off and using the magnetice extender to hold the screws removed. The video on the site was very helpful - the delivery time by partselect.com was impeccable.

I watched the video on utube first, and thought this is a breeze. I'm older and so getting down on my but in the back was what I thought was going to be the hardest part. I removed the screws that held the back plate. Once inside the back I removed the plugs to the heating element with plyers, and the little round thing with nut driver. Ok, what now the video showed where the element just lifted out, mine didn't it was totally encased in the housing. So I felt around to see what was holding it and found a little screw on the backside of the housing, which took some work, and the head lamp so I could see, finally after all that I got the little screw out. The housing for the element still would not come out. so I went back to the video, no help there because the housing on the video just came out and went together about halfway up the housing, mine didn't it was just one piece, so I came here to parts select site and read what other people had said regarding their dryer. I found the information I needed. Thank goodness. I removed the two screws in the front of the lent trap, opened the top of my dryer removed the little Hex nut that held the housing in place, then I went back and removed the heating housing, replaced the element. It was kinda tight, but it fit. I went back to the front put the hex nut back on replace the two nuts in the lent trap closed the top of my dryer, sat back down and replaced that little round thermostate thingy, plugged in the wires to the heating element replaced the back plugged it in and Oh Yeah I had heat. The experience demanded a "High Five" , I felt like a million bucks- this old lady did it herself and the hardest part was having the correct information and getting up and down off the floor. Thanks for all the help!

it was easy to replace the element

unpluged the unit removed exaust, pulled away from wall about 18 inches. Then leaned unit face down, remove back shield/cover also remove he two wires to elements. At the top of housing where element is in there is a screw that needs to be removed, then lift housing element is in side. Slide foward and lift to remove,to replace go in reverse.

ordered and replaced heater element, did not fix the problem so ordered thermal fuse and cycling thermostat when it arrived installed them still did not work. Went to the next item on list thermal cutoff kit ordered it, when it arrived installed and BINGO!!! It works... $107.00 later a dryer that works!!!!!

Replaced the heating element. Everything copacetic.