This grease filter is almost fourteen inches long and almost twelve inches wide. This filter is intended for use with some downdraft cooktops and ranges.
If your stove knob is cracked or worn out, this replacement is a quick and easy fix. It’s black with chrome trim and clear heat settings, so you can adjust your burner from Off to Hi with ease. Made t...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
The surface element control switch adjusts the heat output of your stovetop burner. It has a double flat shaft and is nut-mounted for secure fitting. Ensure compatibility before ordering.
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
This pilot light lens is red and is well under an inch long.
$11.88
In Stock
Questions And Answers for C221
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rick
February 17, 2023
On my Jenn Air model 221C standing behind the stovetop where the knobs are located looking on the right side, the large surface coil is at the back and the small coil is on the front. Both work individually fine from low to high heat. If I cut on the small coil on the front by itself its ok, while it is on low, I cut on the back or large coil and the small coil automatically goes to high. What is my problem? I have replaced both of the infinite switches on that side the small and large burner. I have replaced both the large coil and small one, I replaced the block (ceramic receptacle) that the coils plug into.
Where do I go from here to make it work correctly?
For model number C221
Hello Rick, Thank you for your inquiry. You could have a wiring issue as you have already replaced the parts that normally cause this issue. Check the wiring for any visible damage or loose connections and replace if needed. We hope this helps you.
Are all 4 infinite switches the same on the Jennair C221 Cooktop
For model number C221
Hi Thomas, thank you for the question. Yes, all infinite switches are the same. If your model series is 1, the infinite switches for it are part number PS2076107. If your model series is 5, the infinite switches for it are part number PS12347302. Glad to be of help!
Are the switches infinite or surface element control switch
For model number C221
Hi Samson, thank you for reaching out. The switches are infinite that controls the top elements. Let us know if you have further questions!
Was this helpful?
Thank you for voting!
Ron
February 6, 2025
i NEED 4 BURNERS - 2 measure 7 1/2 inches +- 2 measure 5 3/4 + - I assume you would have the correct size for my Jenn-Air elect cook top model C221 04 serial number 149948NT
thank you for your prompt consideration Ron
For model number C221
Hi Ron,
Thank you for your question. There are both 6 and 8 inch coiled burner elements listed for your cooktop. The part number for the 6-inch standard Y-frame range surface burner is PS11743366. The part number for the 6-inch delta frame surface element is PS11757480. The part number for the 8-inch delta frame surface element is PS11757481. The part number for the 8-inch Y-frame surface burner element is PS11740903. We hope this helps!
What are the cutout dimensions for installing a jenn-air C221 cooktop?
For model number C221
Hello Mike, thank you for your question. The cutout width is 28 7/8th of an inch. And, the cutout depth is 20 15/16th of an inch. Good Luck and have a great day.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!
