C206B-C Jenn-Air Cooktop - Instructions

After examining the burner unit I noticed that one of the male contact spades was burned and look deformed. After removing the spade I discovered that it had been originally manufactured incorrectly. I went on line to try and find the part. I found it at this site . I ordered 2 of the spades and replaced the deformed spade and another one that looked like it had gotten a little hot. She tried the unit and it worked perfectly. She had not used that burner unit for a very lengthy time. The investigation of the problem took a little time, but the repair went very fast. Moral is :" If a spade doesn't look right, it probably isn't", but either the individual spade or plug can be replaced. This site is now my "GO TO" place for parts.

No problem, except the holes in the clips to hold the switch in were so small that the clips would not go over the pegs.
The solution - use supper glue.

This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back!
/John

If you are buying online, i'm sure you know to remove atleast 2 screws! and fit them back. It’s very easy to fix it. Only thing that took time out of the 15 minutes is to push the metallic push nuts! But it was interesting to do that. Partsselect.com is really a good site

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

Took less than 15 mins to remove the old switch and replace for the new one.
Works like new!

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Disable cicuit! remove 2 screws on control housing, lift housing. Remove retaining washers from mounting posts (a trifle difficult, but drill into them with an 1/8" bit...they'll break off enough to grab with needlenose pliers). Mount & wire new switch. The replacement retaining washers are too small...hold them in visegrips & ream the hole with a larger drill bit. Place washer in a magnetic hex drive bit, align over post & tap with hammer to start them, then use a small socket to tap them home. Screw down control housing. Enable circuit...voila!

Easily removed the housing - difficult part was removing old fasteners from posts - took 20 minutes caerfully using knive, needle nose pliers, screw driver. Used old fasteners - new ones provided were too small for posts.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.