All Installation Instructions for Jenn-Air Cooktop C202-C

stove top burner would not heat

new element plugged into burner connection- an easy fix

Parts Used:

Delta Frame Surface Unit - 6 Inch

Marjorie from Indianapolis, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner receptacle was broken

The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Surface Burner Receptacle Kit

Molly Grace from Victoria, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Parts Used:

Range Grease Filter

Martyn from Middletown, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burned out burner

Pulled out the old burner and plugged in the new!

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Esther from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken sens

removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.

Parts Used:

Pilot Light Lens - Red

Dennis from Mahomet, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip pans were in need of replacement

No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

JOANNE from MONKEY ISLAND, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip pans were a mess

Replaced the drip pans

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Chhristopher from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

center piece of the heating element broke off

so easy, just ordered the part, the part came and inserted the element into the stovetop

Parts Used:

Delta Frame Surface Unit - 6 Inch

Elaine from Atascadero, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Receptacle had become bad poor connection.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Parts Used:

Surface Burner Receptacle Kit

JAMES from Harrodsburg, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The control knobs had been damaged by heat

Easily removed the old knobs and applied the new ones.

Parts Used:

Surface Burner Knob Kit

Jery from Knoxville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

Parts Used:

Surface Burner Receptacle Kit