BEP410WB1 Roper Range - Instructions

very easy

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

unscrewed two screws, unpluged two wires, put screws back. turn off power!

I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!

Replaced element.
Looks like I saved at least 500$
Geuss I'm Winning!
:)

Opened circuit breaker, unscrewed old element, disconnected old heating element wire, attached new element wire, screwed new element into place, closed circuit breaker. tested element for heat.

Removed two screws, removed two clips, removed the element and rehooked the two clips and screwed the two clips back in. Zip Zip.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

My daughter told me here oven had quit and ask my advice. I saw where the element was burnt. Took out 2 screws unkooked the wires. I was unable to get help at the local Appl repair store so I went to internet to parts select.com I put in model # and had the part within 3 days put it back in and worked fine.

Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.

I observed that the lower heating element was attached to the lower rear of the oven by two stainless phillips screws. I removed the screws and gently pulled the element outward. The element came out easily with two large red wires attached (one on each side). I unplugged the wires and extracted the old element. I used this as an opportunity to clean the floor of the oven that was hard to get at with the element in place. I installed the new element by plugging in the two red wires and used the same two stainless screws to reattach.

Unscrewed 4 screws holding element. Disengaged one wire, but 2nd one was separated while pulling through rear wall. Could not grasp the wire from the front. Then unscrewed 4 screws along sides of oven to pull casing away from wall cavity. Sat oven on a box while unscrewing 12 rear panel screws. Pulled wire through from back into oven. (Didn't need to do this because new element extended through the rear wall to access from back. Could have reattached wires to new element from the rear, but didn't realize this soon enough.)....two days later reinstalled new broiler element reattaching wires inside the oven and replacing 4 screws holding element in the oven. To replace the back panel I had to lay oven on its face so the holes on back of would fit with the rear panel. Put 12 screws back on. Then pushed oven back into wall cavity and put 4 screws holding oven in place. It is now working!

Easy as 1, 2, 3

The part arrived in less than 2 days. I turned off the main electrical switch to the house. All that had to be done was remove two connecting screws in the back of the oven holding the heating element in place. Then I removed two connecting wires with needle nosed plies. I reversed the process with the new element, turned the power back on, and the element heated up and back in business. This was the easiest I have ever had repairing or replacing anything. The hardest part of this repair was finding a flashlight in my house that had good batteries!! Thank you for such quick and courteous service.