This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$8.99
In Stock
Order within the next 36 mins and your part ships today!
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
$78.99
In Stock
Order within the next 36 mins and your part ships today!
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$51.99
In Stock
Order within the next 36 mins and your part ships today!
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
$68.99
In Stock
Order within the next 36 mins and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$108.99
In Stock
Order within the next 36 mins and your part ships today!
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
$37.99
In Stock
Order within the next 36 mins and your part ships today!
The drain hose carries used water from the washer to your house drain.
$27.99
In Stock
Order within the next 36 mins and your part ships today!
Questions And Answers for ATW4675YQ1
Ask our experts a question about this model and we'll get back to you as soon as possible!
20 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Andy
January 21, 2020
The unit gets bad out of balance when it is spinning. It slams the unit up against the wall and has "walked" it out in the middle of the floor. I found pieces of broken white plastic under the machine.
For model number ATW4675YQ1
Hello and thank you for writing.
This could possibly indicate a malfunctioning suspension PS11703290 and suspension support PS3502189, you should check for signs of damage, and replace the part(s) as needed. It is recommended to replace both parts at the same time. We hope this helps. Please contact us anytime if you require further assistance.
My unit will fill and, when it is about to lock the lid, it stops and the lid lock light is blinking. Is this a problem with the lid lock or something with starting to spin the tub?
For model number ATW4675YQ1
Hello Kevin,
Thank you for your question. Yes, you would need to replace the lid lock under part PS3497627 for your model. Hope this helps!
Hello Cynthia, thank you for your question. The suspension rod kit for this unit is PartSelect Number: PS11703290. Please enter the part number into the site for current price and availability. Good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Kevin
December 16, 2019
I have already replaced the lid lock switch mechanism, twice. The problem still persists. The unit will fill then then attempt to lock the lid. It stops with the lid lock light blinking. What else could be wrong? I need a solution as i am now at the point of not wanting to put any more money into this machine. I hate to do that b/c it is in great condition. What could i be missing?
For model number ATW4675YQ1
Hello Kevin and thanks for writing.
Lid latch # PS3497627 is that the one you installed?
Lid strike # PS11750882
You should try a hard reset first. Go to your breaker box, turn the breaker for your unit off, wait 5 minutes and turn the breaker back on. We hope this helps. Please contact us anytime.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Kevin
December 18, 2019
I have left the machine unplugged all night, no help. I have not replaced the lid strike as it does not appear to be damaged. I don't understand how a magnet inside of plastic could fail. Is there anything else that could keep the lid from locking?
For model number ATW4675YQ1
Hello Kevin, thank you for your question. The only two parts that could cause the lid to not lock would be the lock strike and the lock itself. If the lock was not replaced, we would recommend replacing Part #: PS3497627. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
