ASI2575GRS08 Amana Refrigerator - Instructions

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Pried out the old switch and installed the new switch.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Replacement part arrived via FedEx package with one hinge already broken off, unable to install. Still waiting on requested replacement.

Remove 4 self tap screws holding on front cover/bin handle. Remove 2 self tap screws holding drum cover. Remove 1 self tap screw at back of bin holding door actuating rod and spring, slide forward to disengage. Remove "E" clip and flat washer. Remove plastic nut {clockwise/left hand threads]and remove crusher parts [keep in order removed]. Slide new drum on shaft and reassemble crusher in reverse order. Install drum cover w/2 self tap screws. Install flat washer and "E" clip. Re install actuator rod and spring assy. Install front cover and test in refrigerator. The 2 self tap screws that hold drum cover are easier to remove with a 1/4' drive ratchet and 1/4" socket because of limited space behind actuator rod. This job is a snap to do. I'm sure it's at least $50.00 cheaper than a service call.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

installed new parts

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Great service. Unpluged old switch and pluged in new one. Works great

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.