ASI2175GRB03 Maytag Refrigerator - Instructions

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

On a side by side refer, you need both doors open to unscrew the three 1/4 inch screws,
1. Remove the ice tray
2.the ice arm needs to be in the up position, so no water will flow while dissembling.
3. Remove the two top screws,
4. While holding the ice maker with o e hand, remove the bottom screw.
Balance the ice maker and unplug the ice make electric plug in the rear of the ice maker.
5. Take the I e maker out.
6. The ice maker does not come with the ice arm, so you need to remove the arm from the old or broken ice maker and install it in the new ice maker.
7. Resemble in reverse order.

I did not unplug the refer from the wall socket, you may want to do this. It recommended but I did not.
There you go.

Took off the cover, pulled out the old filter, inserted the new one and closed the door.

First off you need to shut off the water supply valve that goes to the icemaker. Next pull the refrigerator from the wall , thats the fun part. I did not unplug my refrigerator when I did this . You can to be extra safe. At the bottom on the back side remove the cardboard cover on the bottom like four or five screws and set this aside. The water valve is on the bottom on the right side. There are 3 water lines attached to it. Having a towel handy might be helpfull. 1 line supplys the water, 1 is for the water dispenser and 1 is for the ice maker. These are push in connections no wrench needed. Remove the 2 screws that attach water valve to frame. Arrange it to make removing the 2 wire connections and water lines easier to remove. Wire connections just pull off. Mark them as to what valve they go to. Next remove the water lines. you need to remove a plastic lock that insures that the water lines do not pop off, very simple. Next push down on the nylon connector push down on the top of connector and pull on the plastic water line at the same time and it will come out. Do this to all 3 water lines. Remove old water valve and install new one in the reverse order. The water lines just push in no need to mess with connector when line is in reinsert the plastic lock. Reconnect the power connections. Align the water valve bracket with screw holes in frame and reattach the 2 screws holding it in place. Now would be a good time to turn on the water and check for leaks. You can check water dipenser but ice maker has a mind of its own. If all is good reinstall the cardboard cover on the back bottom and push refrigerator back where it was. Make sure the water line is not kinked. Aftre a couple of hours the ice maker should start making ice.

Removed ice bin then pulled front cover with nut driver . Pull small rod from side ( one screw holding rod and spring). Pull auger out. Take plastic nut off end ( CLOCKWISE) LEFT HAND THREAD. Keep all ice crusher blades in order when you pull them off. Install new auger and reverse steps. web site has exploded view. It looks difficult but it isn't.

When the filter arrived, I removed it from the package.
Upon reading the instructions, I removed the old filter.
When I removed the old filter I NOTICED HOW IT CAME
OUT SO THAT I COULD HOLD THE NEW FILTER IN
THE SAME POSITION AND REPLACED IT WITH THE
NEW IN THE SAME POSITION. When I closed the cover
door, I went to the display panel and reset water filter display.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Removed the rear cardboard cover and cleaned the area around the compressor and as much of the condensor and fan area as possible. Removed the two base section securing bolts. Jacked the rear of the cabinet up enough to seperate the base from the cabinet. Removed the roller pins and removed and replaced both rollers. Lowered the cabinet back into place, replaced the base bolts and the cardboard cover. The rollers that were sent were of much better quality than the original plastic type and should last the life of the refrigerator. Be careful when moving the fridge as the original rollers may cut into or scratch the flooring.

Lift up on the water filter door to open. Pull out the old filter while noticing the arrow pointing up on the filter. Pull off the green caps on the new filter and pop the new filter in with the arrow pointing up as on the old filter. Push in until the filter snaps into place. Close the filter door. Push reset on the water filter button on the freezer door to reset. Very easy!

Simple, turn and pull to remove. Push and turn to install.

Unplug the fridge then wheel the refrigerator out to where you can get to the back - you will probably have to disconnect the ice maker water hose. Using the nut driver remove all the screws from the lower panel on the fridge. You will not have to remove the water hose connection just move the panel around a little. Look on the left side (facing the back of the fridge) you will see the capacitor held onto the compressor with a spring clip. Just pull the clip toward you and that will free the capacitor. Pull up on the capacitor and that will unplug it from the compressor. Be careful not to touch the two poles on the old capacitor. Capacitors store electricity and it could give you a jolt. I used electrical tape to insulate the poles and then threw it away. Plug in the new capacitor- re-hook the clip, reinstall the back panel, plug it in and verify that the fridge is working. Hook your water hose back up and move it back into place and you are done.

Checked the water line from the wall to the supply port of the inlet valve and it was suppling water but no water beyond the water inlet valve, So I ordered a new inlet valve and installed, and it fixed the problem. Inlet valve supplies water to the ice maker and water dispenser filter housing. Partselect videos and you tube installation videos very helpful. Partselect troubleshooting guide also very helpful. Great company

Shut off water supply. Unplug refrigerator. Removed lower back cardboard panel. Removed two screws holding inlet valve bracket to side frame. Pulled valve out far enough to gain access to water lines and electrical connectors. Used 9mm open end wrench to press in collars to remove water lines from inlet valve. Used small container to catch water dripping from lines. Removed defective valve and replaced with new one by first pushing water lines into respective openings, make sure they are fully seated. Reconnected electric wires. Installed inlet valve on side frame. Replaced back panel. Plugged in power cord. Opened water supply. Flushed about 2 gals of water through system. Note: water may not flow immediately due to air in water lines.