AS2126PIHW Maytag Refrigerator - Instructions

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

1. mark location of removable baskets in door and remove baskets
2. remove three screws in top hinge - save shim under hinge
3. lift door from lower hinge
4. remove 3 screws from lower hinge bracket and remove bracket
5. install lower hinge bracket with 3 mounting screws
6. install lower hinge pin in bracket
7. clean upper and lower hinge holes in door
8. lubricate upper and lower hinge pins with grease
9. place door over lower hinge pin - the magnetic seals will hold it in place
10. install upper hinge bracket with 3 screws
11. install baskets in door

Note: The plastic piece on the bottom of the door that mates with the hinge pin and provides a cam action should have been replaced at the same time.

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

Removed the food out of the fresh food door. Removed the top hinge cover, removed the 3 nut screws on top. Lifted the door off of the bottom pin. Set the door to one side. Removed the lower hinge pin with a screw driver and replaced with new product. Lifted door back onto lower hinge pin, secured the top pin hinge with the 3 nut screws, replaced the top hinge cover and placed food back into the door. Done in less than 15 minutes.

Great service. Unpluged old switch and pluged in new one. Works great

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT