ART2127AW Amana Refrigerator - Instructions

I followed the instructions that came with the refrigerator and those that came with the gasket. Everything went smooth and fast. It is best to take the door off the refrigerator and lay it down and then do the replacement.

replaced the entire ice make - 3 screws and a squeeze -off connector and it's out. Reverse to re-install... except that the fill tube had iced up. To thaw the fill tube: unload freezer section (leave food in fridge, but keep door closed), remove ice maker. Boil water, dip drill bit (dull end) into hot water, swirl around, insert (dull end) into to fill tube. Depending on how hot you got it, maybe a tablespoon of ice will melt. Repeat many times - fill tube is about 14" long! Do not use anything sharp - you will nick the tube and ice will form causing you to repeat this procedure. Do not try to break the ice - let the heat work. It took me about 30 minutes to thaw the whole thing - it made a nive gasping noise when the final plug opened up. Re-install ice maker.

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

just cleaned it and put in place. I was really impressed as to how fast it was sent to me. I broke it on Nov. 1 and placed the order that afternoon and received the new glass on Saturday Nov. 3. I really appreciated that as I never expected it until the following week. Thank you for the fast service!

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

Very simple fix, remove 3 screws, two connectors to the old switch

remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will fall..all done.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

I just followed the directions on the video of my specific model. Make a note of where to locate that video of your model, as there are many other videos of other models that can have different parts located in different areas and it can be time consuming finding the exact video you want again.
Also note that you must make mental or written notes on exactly what direction any parts you remove are facing, this can save huge amounts of time when reassembling.
I was worried that I might need other parts, but decided to do one part replacement at a time since this unit is a spare and no urgency to get it back working again. I found that the evaporator fan was the only thing needed! The fridge works like new again!

, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.

Take off freezer door to take off refrigerator door. Once fridge door off, put freezer door back on, lightly screw in place. Lay fridge door down flat on table. Take out all screws. Put new gasket in, while putting a few screws in to hold in place. Screw down. Use blow dryer to help get any kinks out. Easier than I thought it would be. I think my door is a little warped, but the gasket was enough to make it seal. No more condensation, and the fridge isn’t running all the time. Thanks parts people! Haha.