ARB210BAC Amana Refrigerator - Instructions

First I removed all the screws with the exception of the top row, these I just loosend.I made sure how the old one was installed before I removed it.I then used a hair dryer on the new one briefly to take out the shipping kinks.I removed the old one and put the new one in with a little adjusting as i went. I then put all the screws back in,adjusted it a little more and finished by snuging up all the screws.It was very easy and works like new.

unplugged the range, removed 5 screws from the back cover and removed the knob and two screws holding the switch to the range. oriented the new switch to the old one and changed over the wires one at a time to the new switch, reattached the new switch to the range plugged the oven back in to test new switch and reassembled

I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00

Turn freezer section control wheel off, unplug unit. Then remove all items/baskets from freezer to allow access. Use nut driver to unscrew 3 screws on control plastic housing. Drop down housing from top and unplug wires (note correct locations) from control wheel switch. Remove screws and ground wire from metal backing plate to plastic housing. Push or pry the 2 metal holdtabs down carefully to allow the 2 plastic housing tab fingers to be pushed inwards to seperate metal plate from housing. Pry control wheel off from switch arm with screwdriver. Remove switch and replace with new one.
Use the reverse order of removal above to replace into freezer but use caution when replacing wheel onto switch arm and plugging in wires. Remember to carefully pry the 2 metal tabs back up to secure the plastic finger tabs in place.
Job done.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

I hired someone to do this, but after watching him do it, this is an easy job. Amana made a smart refrigerator and it's easy to do your self. I saved a LOT of money buying the parts here and I should have attempted it myself. The trick is heating up the gasket once it was mounted and then when you had a tight seal to the door, tape the door shut and LEAVE it as many hours as you can (minimum of 4, but overnight better).

I removed the Icemaker then the backpanel in the freezer. The fan motor removal required only to hex screws and three wires to dismount. The biggest problem I had was the replacement motor had the connecting pins for the wire harness on the reverse side. I thought I could unbolt the motor and flip it but this did not work. I remounted the new motor and was able to get the wires connected. The thermostat clipped in place but one of the wires had a different connector than the new unit. I used a wiring snap connector to complete the connection. The defroster timer was under the refridgerator and after taking two screws off the cover plate was just an unplug and plug in the new unit. When I first turn the unit back on nothing happend. I soon realized I had to advance the timer until the unit kick on. It has worked fine since and solve both the noise problem and defrost issue.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

1st remove the gasket from the packaging & let it get to room temperature . 2nd use a hair dryer to get it in shape . 3rd cut out a piece of the box that the door gasket was delivered in to cover the freezer opening after you remove the door,4th(remove the door by removing the bottom hinge) 5th put the door on a table to remove the old gasket with a screw gun,(now is a good time to clean the door up) after the old gasket & panel was removed I found the insulation inside the door panel frozen solid so I replaced it .If you don't replace this fiberglass insulation or a least try to thaw it out you defeat the purpose of the doors insulations R value. 6th replace the gasket (replace the gasket the same way that you removed it) 7th put the door back on the freezer.You don't have to remove the freezer door to do this job but it makes a much neater job & a better seal when the door is closed. This isn't the 1st door gasket I replaced so I kind of knew what I was doing.Good Luck

I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

While investigating a water leak I discovered the condenser fan seized. I removed the fan to prevent a fire and ordered the part. The hardest part was identifying the correct fan. That took longer than the installation.
I cut the wires and spliced in the new motor. It rotated correctly and I replaced the crill.
Done
Total time of ice maker water leak repair and fan replacement about 1 hour.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

1. Removed the cardboard cover.
2. Removed the terminal block and unplugged the old motor.
3. Removed three screws that held old motor to the bracket.
4. Removed the fan blade from the old motor.
5. Installed the fan blade (after cleaning) to the new motor.
6. Crimped on new wire terminals onto the leads on the new motor.
7. Installed the new motor using the fasteners provided.
8. Plugged the new motor wires onto the proper terminals in the terminal block.
9. remounted the terminal block.
10. reinstalled the cardboard cover.